x devil mk2 3d models

devil's head

After installing the MK2.5 upgrade on my printer, I encountered a problem during calibration - the carriage couldn't engage the x end stop. To resolve this issue, I made a straightforward adjustment to the original code and increased the length of...

I've modified the Prusa MK2 x-carriage using standard 623 ball bearings. This carriage glides smoothly without any backlash on slightly rough smooth rods. It fits perfectly to the Prusa MK2 extruder body. A few modifications were made to the...

I created this to deal with alignment issues when using MK2.3 extruder from this model – https://www.thingiverse.com/thing:2735475I rebuilt the extruder with 4010 extruder fan, now endstop needs to be a bit farther out or the fan collides with the...

(25.4mm flange, 19.05mm center-to-center screw hole spacing, 12.7mm OD of throat for leadscrew) * 2x M3 x 12 screws * 2x M3 nuts * 2x M2 x 12 screws * 2x M2 nuts * (+Other screws/parts/etc that make up the Prusa X-Ends) Included are my modifications...

You'll need: * 2 x POM nuts from RobotDigg (25.4mm flange, 19.05mm center-to-center screw hole spacing, 12.7mm OD of throat for leadscrew) * 2 x M3x12 screws * 2 x M3 nuts * 2 x M2x12 screws * 2 x M2 nuts * (+Other screws/parts/etc that make up the...

This is my version of X axis cap for cetus3d mk2 extended. It is part of conversion to opensource tinyfab MCU, that requires mecanical switch for endstops. I tried to model this thing in a minimal and elegant manner. Use two M2.5 12mm screws to...

This new design is specifically intended for the renowned Prusa i3 MK2-X, designed by davtr, which can be found here: https://www.thingiverse.com/thing:1692666. Recently, I acquired the multicolour upgrade and discovered that the extruders are...

This is a custom X axis cap designed specifically for the Cetus3D mk2 extended. It's an essential component of my conversion to open-source TinyFab MCU, which necessitates a mechanical switch for endstops. To assemble this cap, you'll need two M2.5...

I created this to deal with alignment issues when using MK2.3 extruder from this model – https://www.thingiverse.com/thing:2735475I rebuilt the extruder with 4010 extruder fan, now endstop needs to be a bit farther out or the fan collides with the...

Since I am running a custom MK2 clone, I wanted something close to the original with little modification, Enter the new x ends. This is a modification of the x-ends from the prusa openscad files to include a 3mm hole on one side (normal) and a 2mm...

MK2S / MK2.5 Webcam mount to monitor prints remotely whilst away from the printer. I've designed this mount to work with any standard tripod screw although the screw will need to be long enough to go through the 10mm arm prior to to screwing to your...

On my Prusa, the x rod tensioner screws causing belt tension also put stress on the z-axis motor mounts and top z-axis rod mounts at the top, resulting in excessive friction and binding. Since I needed just a bit more tension on the belt, I wanted to...

Adjusted to precision, the editing screw functions seamlessly like its original counterpart on the stock mk3 model. ...Simply rotate the X-axis motor by tweaking the top screw to achieve optimal performance.

Original piece from Prusa (/https://www.prusa3d.com/prusa-i3-printable-parts/) , with following modifications A channel for inserting the cables instead of having a hole requiring major disassembly for cable settings: x-carriage-back-cable_slot.jpg...

You can see these modifications in the images of x-carriage-back-cable-channel1.jpg and x-carriage-back-cable-channel2.jpg. To provide additional support for the cables, I've added some material to the wall between the cable slot and belt slot, as...

This is a precision-made X-Brace designed to guarantee that M10 threaded rods are perfectly parallel on the Original Prusa i3's Y-Axis. I fabricated this by printing it flat on the bed of my printer. ... Print Specifications: Rafts: Completely...

Assemble the plate on to the X-Axis motor with (4x) M3 x 10mm screws, I had these in my Spare Parts Bag. Install (3x) of the square M3 nuts (also in Spare Parts Bag) in the slots then assemble to the mount, leave slightly loose. I used a screw driver...

I, like many others, experienced a frustrating issue with my 3D printer's belt wearing down prematurely due to a misaligned belt holder on the x-carriage. I scoured the internet for solutions, but most threads only scratched the surface of the...

Humans strive to rival the devil by mastering 3D printing technology.

Ready to print Devil, with perfect topology, and high resolution of polygon. ...Comes in the following formats: .Stl .Obj Have fun :)

I created this devil in Zbrush just for kicks, I'm a total newbie. Check out my channel on YouTube and subscribe - it's the best way to stay up-to-date with all my latest projects! ...Print Settings: Resolution: 0.2 mm Infill: 10% This model supports...

Making a devil potato is all about adding some serious heat to your spud game. First, preheat your oven to 400 degrees Fahrenheit, because we're about to get this party started. Now, take a large potato and give it a good scrubbing under cold water,...

X-Carriage compatible with the MK2.5(S) Bondtech Prusa Extruder with the Revised X-axis https://www.bondtech.se/en/product-category/upgrade-kits/prusa/ and https://www.thingiverse.com/thing:3559732 This X-Carriage is designed to work exclusively with...

Simple x-axis cover against dust and dirt.Remove from the printer before printing!Jednoduchý kryt osy x proti prachu a nečistotám.Před tiskem odstranit z tiskárny!

This text appears to be a set of assembly instructions for a 3D printer, specifically the RebeliX. It is written in a clear and concise manner, with each step building on the previous one to guide the reader through the process of assembling the...

You can enhance your Anycubic i3 Mega X-Carriage [MK2] with covers. ...Have fun printing!

Now you can easily upgrade your Original Prusa Mk2.5/Mk2.5S to use the new Mk3S+ extruder.This part replaces “endstop-block.stl” from the official Prusa3D parts github with an X-axis end-stop switch actuator built into a fan cover. The fan cover...

Changed model of both Prusa MK2.5 and MK3 X end Motor mount. ...It is dedicated to MK2.5 so it is possible to apply a belt tensioner to it.

Changed model of both Prusa MK2.5 and MK3 X end Motor mount. ...It is dedicated to MK2.5 so it is possible to apply a belt tensioner to it.