xhover stingy v2 3d models

Secure your HS1177 style camera with precision using these TPU mounts that fit snugly onto your standoffs. Available in two angles - 35° or 40° - they provide a rock-solid base for your FPV camera. Simply slip the mount over the standoff, slide the...

Finally combined the TBS Immortal T with the Bardpole. ... Designed for use with TBS Crossfire nano diversity, which supports two antennas.

The Team Played Unbeaten 100% for X Hover Win 5 / R5 X / RX 5 LX

Human: GoPro gap is filled by a sturdy frame mount.

I'm thrilled with the long Range Antenna Mount's design, and I've found it pairs perfectly with my Air Unit Mount to ensure a secure connection without applying any pressure on the MMCX connectors. Check out the photos for more details. This mount...

If you need a Team Blacksheep Immortal T holder just for your Win5, this design might work for the Win3 or Win4 as well. To assemble it correctly, print the holder in TPU or any other flexible material that allows you to open up the hooks and get the...

I perfected the design of the SMA and immortal T combination, merging them into a single print and incorporating screw holes for unified style cables. ...What are your thoughts?

This mount securely holds the Runcam Swift Micro 2 in place while safeguarding the quad's front and camera from potential crash damage.

The person operating this device is holding a 20-degree angle positioning tool known as the Skyeliner, which is used to secure a GoPro camera session. ...The Skyeliner has been attached for five consecutive sessions.

I got fed up with constantly snapping battery straps in crashes while racing my R5LX and R5X. So, I took matters into my own hands and designed a plate that deflects the angle away from the plates. As a result, the battery strap is now pulling...

Le Drib Skeyeliner Antenna Mount. Designed with three zip tie slots and one vertical slot to secure a horizontal antenna, this mount wraps snugly around a standoff. A built-in SMA connector mount is also included. ...Dimensions are approximate, but...

I engineered this setup to integrate seamlessly with an RMRC LED light bar positioned at the rear of the vehicle, specifically designed for high-speed racing quads.

The group known as Altare del Santo comprised a total of twenty-nine pieces of sculpture. Among them, four bronze bas-reliefs depicted the miracles of Saint Anthony: the Miracle of the Ass, the Miracle of the New-born Child, the Miracle of the...

We're enhancing the design to minimize oscillation, while boosting ink saturation for a richer finish.

The LR Blink Mount! Print it in pop-up color so if the mount ejects from the frame, you can easily spot your GoPro. Also, the mount is designed to keep the GoPro securely inside, no matter what. You can count on that fact every time. A strap is also...

Printed with anycubic mega S TPU A95 and A98 Print Settings: 3 Walls 2 Top 3 Bottom 100 % infill No supports print speed 30 mm/s I added the component with base since I had some issues with adhesion to the board. ... Enjoy !

I made two versions of this, 35 and 40 degrees, because why not? They both fit snugly and have a super minimalist look that I'm really digging. ... Check out the original design here: https://www.thingiverse.com/thing:2263851 After taking my camera...

I went to take the drone out for a spin and accidentally knocked over the camera, which unfortunately got damaged. I had to come up with an alternative solution using the Fatshark I happened to have on hand. I printed it using my Impressora 3D...

I reworked it to match my initial post, and now it's angled 25 degrees upwards, featuring a 7mm-long aperture paired with the same 7mm diameter as before.

I have made it flat on one side, so print it sideways with brim. worked nicely for me. ...the camera mount is with 25°

print in TPU

After creating my original, I took it for a spin and the camera got knocked out of commission. Had to design an alternative version that would fit my trusty Fatshark. Printed it up on my RepRap using flexible rubber filament from Impressora. No glue...

I'd like to introduce you to a cutting-edge AXII U.FL Mount, specifically designed for use with the powerful FrSky RX Antenna. ...This meticulously crafted accessory is built from high-quality TPU materials that ensure a seamless integration and optimal...

These prototypes may prove to be effective, but I've yet to put them to the test. ...They show promise nonetheless.

V2 Kayak propeller V2

V2

v2

Schleuder V2 / Slingshot V2 Get Ready to Blast Off Print Settings Printer: CTC Rafts: Don't Bother, It's a Breeze Supports: No Way Resolution: 0.1-0.2mm - That's Tiny! ...Infill: 30-50% - Just Right Notes: 5 Shells Waiting to Explode

lcd128x64_v2

crazy v2