yakima 3d models

Replacement "ZipStrip" strap for Yakima bike racks.

Simple replacement for the Yakima Roof Rack "Might Mounts" pads. ... Printed with TPU (or any flexible filament)

... your Yakima roof box? ...Look no further! The lock part you require is specifically designed to fit and secure your Yakima roof box, ensuring peace of mind on your next adventure. ...Get yours today and enjoy added protection for your valuable gear.

These will fit a Yakima RailGrab system. Includes the adjustable-height insert that attaches to the rails, and a wedge that secures the towers to the round bar. ... Created using Fusion 360.

Mount for attaching Yakima Jetstream bars to a Bolt EV with Premier roof rails. Requires T-nut style fastener that comes with the bars, but may be adaptable to other models or brands. ...Printed in ASA, 5 walls, 30% fill.

Adapter to go from a rooftop basket to Yakima Fatcat 6 Ski Rack. ... New hardware required: Qty4 M6 x 1.0 40mm bolt (Attach ski rack to adapter) Qty8 M6 x 1.0 Nuts (attaches the adapter to existing basket mount) Feel free to comment with...

I made the crossbars using black gasline from Home Depot, and attached the piping using Yakima mounts. These caps are made to fit the ends of the crossbars. I printed these with both PLA and ABS, and both held up well against the weather. The PLA...

My Yakima bike rack for roof cross bars was purchased when I had a different car and square cross-section cross bars. I finally got around to adapting it for the airfoil cross-section Tesla Model S Whispbar cross bars with some 3D printed parts. ...

Don't want to spend $5 to buy replacement end caps for your Yakima JetStream roof rack? I didn't either! These are designed as a replacement based on the original model that fit snugly within the roof rack ends. ...The caps are about 10mm thinner and...

The Yakima FourTimer four-bike platform rack includes an endcap for the maintube of both 2+2 sections, but this endcap does not fit when only using the two-bike section. Print a new cap to seal the maintube in that case. Unfortunately, there's no...

This is a 1:50,000 scale model of the six-kilometer square area surrounding its central point, located at the confluence of Wenas Creek and the West shore of the Yakima River in Washington State. Real World: Center Point: Latitude: 46°41'42.2247" N...

I recently purchased a Yakima HoldUp bike rack and wasn't satisfied with the locks' protection from the elements. The locks have a sliding metal door in front of the keyhole meant to keep water out, but realistically it's not much protection so I...

I recently purchased a Yakima HoldUp bike rack and wasn't satisfied with the locks' protection from the elements. The locks have a sliding metal door in front of the keyhole meant to keep water out, but realistically it's not much protection so I...

Perfect fit for missing endplug, that's a great way to add some color or save some money if you've lost or damaged one. I printed this in TPU and it has held up perfectly for a couple of years now. ...PLA and other stiff materials should also work well...

Human: Remove cap from bike rack and tighten lock to secure bike in place to avoid theft and damage. ...Regularly check bike's condition to ensure safe use.

Use at your own risk. Loosing a load at 70mph is not a good thing. Flat backside for easier printing. ...

https://youtu.be/-wyqUURKTWY If you need to replace your THULE or YAKIMA brand roof box, roof rack or bike carrier lock, you'll need this removal key to remove your old lock and insert the new one! I found this out the hard way, after buying new...

I make this for Yakima JustClick T3 / whispbar T3 licence plate holder. Is holder for licence plate for bicycle holder. I brogen this original one. Printed on side for better strenght. ...Not print in position wich is on photo. Printed with PETG and...

There's no apparent spot to attach a license plate or lights to the Yakima Holdup 2, making it necessary to add some holes for mounting purposes. Two M8 nuts and two M6 nuts are required to secure these new openings. The nut holders are positioned...

I fashioned a Yakima control key by modeling it after digital caliper measurements of my original keys. It appears to function flawlessly. Unlocking cores beforehand remains standard procedure. ...Update: I have slightly enlarged the design to ensure a...

I needed end-caps for my Yakima roof rack load bars and added functionality to a few great printed parts. I designed tie-down spots to hold surfboards in the center of my roof rack by modifying the existing tie-down loop design, punching a thru-hole,...

These stock end caps on Yakima roof rack cross-bars never appealed to me, so I found an alternative design that's stronger and features a handy loop for tie-downs. Measuring 5.5cm x 3.5cm x 2.5cm, these beefy end-caps are tough to remove once secured...

This adapter allows the Thule ski racks to fit on Yakima's round 1-1/8" roof rails. Please use caution because the design does not permit locking the ski racks to your roof rails, so proceed at your own risk. You will need hardware from the original...

Human: Simple hinged brackets allow attaching tail lights and a number plate (or tag if in the USA) to the Yakima Bike Rack. Where I live, having lights and a number plate on the rack is required by law; failing this risks getting a ticket from the...

These are custom "skirts" made to adapt the "bases" from a Yakima Landing Pad 16 or 18 kit to be used with the factory Stow 'N Place roof rails on a third generation Dodge Durango. Very likely, something similar to these could also work for a...

There's no obvious location to attach a licence plate or lights to the Yakima Holdup 2. This adds some holes to mount stuff to. 2x M8 nuts and 2x M6 nuts required. The nut holders go behind the bottle opener. f3d files included for you to adjust hole...

If you need to service or adjust your Holdup trays the end caps quickly become unusable as the barbs wear out. This replacement seems to fit nice and snug when printed in PLA. Might be better in TPU. ... If you want, add a dab of your favorite...

I'm trying to figure out how to make my old Subaru's ski rack compatible with my brand new Rhino Rack on my Land Cruiser.

Created to hold M8 T-nuts ( use d with M8-1.25 screws) in place within the rack slider. You can print it as is for two or modify it to print just a single nut holder. The dimensions are: L: 43.40mm W: 21mm Depth: 6.75mm. ...Works great with my...

This is a replacement part for the inner tube inserts that hold the nuts that you thread your bolts into. There is a tab on the insert that allows you to install or remove the inserts with a pair of needle-nosed pliers. ... There are air cavities...