yongnuo twin flash diffuser 3d models

Today is all about sparking creativity and inspiration to create something truly amazing - a light diffuser that adds a personal touch to any space. I designed this diffuser as a tealight holder initially, but I'm excited to share it with you in its...

This is my first upload. ...Feel free to leave comments on how to improve things in the future. Sits on a desk to hold a standard downlight and diffuser sheets. ...Sheets were cut from salvaged parts from a TV screen to 13cm squares.

A replacement diffuser shade for C7 night lights clips onto lampholders using a 0.675" x 0.175" holder. Do not use this product with an incandescent lamp, as there is limited clearance in the shade to dissipate heat. ...This part should only be used...

Here are some additional features that were implemented in RAE M2129 S-Duct diffuser Test Case: Model generated using NASA plot3d grid data: https://www.grc.nasa.gov/WWW/wind/valid/sduct/sduct01/sduct01.html Precise positions and rake probe locations...

... should also work well in PLA too. ...Use support material as needed, and note that there is an overhang on the clips which fit perfectly over the standard colored diffuser. ...Designed specifically to distribute light evenly when used inside a tent.

diffuse you LEDs! Be sure to read the manual to see how. STLs for reference only. Use openSCAD/Customizer to customize to your setup. need a box? ...https://www.thingiverse.com/thing:5754914 please only post remixes that are not from...

Replacement Diffuser clip for Utilitech Fluorescent Flushmount Ceiling Fixture Model #: MXL 203 More info: http://pdf.lowes.com/productdocuments/34070851-afbe-453f-a11d-5e993433c314/03265281.pdf Printing: Need supports. Either use ABS or very high...

This is a diffuser case for the [Pixel Badge](https://pixel.curious.supplies), an ESP32 WiFi LED panel that runs on the open source [badge.team firmware](https://github.com/badgeteam/ESP32-platform-firmware) and is programmable in Python. ...

A compact, low-cost alternative to the Nanoleaf Aurora, this miniature diffuser harnesses the power of NeoPixels to create a mesmerizing display. Simply connect these tiny lights to your preferred controller and get ready for an immersive experience....

... on their preferences and specific situations. ...Ideal for illuminating campsites or enhancing road safety while cycling. Designers can print this torch diffuser in clear or transparent materials, such as PETG or ASA, to maximize light penetration.

I have an Essential oil diffuser and I needed a place to put the oils. I designed this to take 6mm balls to make it spin smoothly, but it doesn't need it at all. ...The carousel spins really well without the bearings.

Designed a custom diffuser for a colorful LED light utilizing Tinkercad, available online for editing at https://www.tinkercad.com/things/5VRAGhcl5Jo. ... Instructions: Manufactured the design using a Makerbot Mini 3D printer with optimized settings of...

Turn any flashlight into a radiant lantern with this fully customizable diffuser. Measure the outer diameter of the light source to ensure a precise fit, then adjust the settings to suit your preferences. For optimal results, print in white,...

... and disturbing the dust I was trying to vacuum up. ... This diffuser sticks in to the outlet and disperses the air upward, away from the work surface. ... This is a work in progress with the next steps to add the little nubs to retain it in the outlet.

I designed a basic diffuser holder that securely fits over the MSPEC Shift Light for iRacing drivers. The lens is carefully cut out of a plastic milk bottle. ... Print Settings: Printer: Cocoon Create Rafts: No Supports: No Infill: 100% ...

It's very simple to install, just slightly bend the middle LED away from the housing, just enough so that the diffuser slides into place, over the LED. It should stay in place without any adhesive. I used transparent PLA for this print for light...

I recently installed an Enermax-ETS-T50 CPU cooler for my son, but I was disappointed to find that its LEDs were quite overpowering when viewed from a certain angle while he sat at his computer, so I came up with a clever solution - a diffuser insert...

This is an attachment to GODOX V860 flashlight. ... its purpose is to difffuse the original flashlight.If the fitting is too tight just dip the base of the diffuser int he hot water just for a few seconds then fit it.

A replacement diffuser for the Nikon SB24 Speedlight. A push fit that doesn't fall off easily. For best results print in a white PETG with a low layer height (max 01.5mm). ...Print instructions PETG 0.15mm layer height 4 perimeters Infill doesn't...

This is a diffuser for the blower of the handheld Wyze vacuum. Since the exhaust is located at the bottom of the device it would blow away all the papers (and dust) when I used it to vacuum my desk (for example). ...This redirects the exhaust to the...

I made a basic diffuser for my Streamlight Microstream USB, printed it in clear PET-G and it looked great, so I tweaked some parameters, ended up with a cool little lightsaber that my kid will love to play with. ...I might even cut a gel-filter to...

A diffuser with anti-glare screen for the Nitecore MH12 V2 This object works together with: Nitecore MH12 V2 Tripod Base: https://www.thingiverse.com/thing:4797675 Nitecore MH12 V2 Backpack Organizer: https://www.thingiverse.com/thing:4797688 Hope...

This diffuser has an impressive design, and I've included all necessary STL files for your convenience. Please don't forget to scale the model according to your specific requirements before incorporating it into your project. ...It's also a great fit...

You can create your own custom diffuser for the Fenix PD32 flashlight, which I made glow-in-the-dark but white is also an option. ...Here are my printing instructions using a Mendel90 printer: layer height of 0.1mm, 20% fill, and ensure support touches...

... printed wihout support but I still advise you to use tree support to be sure it print well. Designed around this diffuser : Softbox Godox SB1010 The elliptical one fits a bit better but I still provide a rectangle one, it might be easier to modify

Aquarium Water Diffuser. To fit hose 13mm-1/2" ID. If using included clamp file, OD is 17mm-11/16", otherwise you can use any appropriate size hose clamp from your local hardware store. The clamp will require 2 M3X14mm fasteners + 2 M3...

Print Settings: Rafts: No Supports: Yes Resolution: 0.2 mm Infill: 0 % Notes: I printed the diffuser on a Prusa i3 with Cura 15.04.3 slicer. ...To print it properly just as a hollow shell with one end opened, I used the following settings: Layer...

The Astrolux WP1 diffuser cap is great at diffusing, but unfortunately it also diffuses away the often needed hot-spot of the beam too, seriously limiting the torches throw. I've created this customisable cap that snugly fits the torch, and done...

I printed a complete set of Tanya Wiesner's Melting Candle Tea Light Candle Holders from MyMiniFactory and created a flame diffuser to fit over these LED Lights:...

... aesthetic. This intricate design was meticulously modeled using the powerful Fusion 360 software. Check out the inspiring project on Reddit: https://www.reddit.com/r/flashlight/comments/a6q66t/3d_printed_2_part_diffuser_cap_for_olight_m22