z sync kit for creality cr series 3d models

For my CR-10 Max I did my own kit which allows you to use belt which different length (approx. 1200mm to 1600mm). This Kit only works with the “on top of flipped brackets” pulley setup, but is very minimal and creates not unsymmetric pulling force on...

<p>Mine cracked and didn't find a model online. ...I know it fits the Creality CR-6 SE and the CR-6 Max, it may fit others but I don't have other printers to check.&nbsp;

Just notched out the bracket a bit for the CR Touch cable to clearance. ...Original model works fine, but puts too much stress on the small wires.

This is a slight adjustment to the Z Axis motor mount I needed after installing the "Creality CR-10 Wire management, Strain relief and Glass holder" https://www.thingiverse.com/thing:2328449 which I found impacted the corner of the motoer mount,...

This part was specifically designed for the CR-10 printer's older model. It replaces the stock Z motor tiny bracket that holds the motor in place from the side, but only partially since the motor still moves around due to lack of proper mounting from...

The solution addresses a common issue affecting CR-10S and upgraded CR-10 models: when the Z axis moves, the X beam's downward motion causes the right carriage lower edge to brush against the second motor support slightly before the left carriage...

Replacement part for the CR-10 Z rod top brace. One variant holds the stock bearing. Another variant is bearing-free, in case the bearing is too tight. Another variant uses a standard 608zz or 608rs bearing. Two M3 x 14 screws are used to attach the...

Z-Axis Steppermotor clamp is designed for CR-10, requiring no additional screws. However, the top screws are slightly too long, necessitating a spacer, washer, or bigger nut to secure them properly, while also ensuring free movement of the heat bed....

This is a precision replacement Z stepper motor bracket engineered specifically for the Creality CR10. It enables effortless adjustment, ensuring optimal alignment with the lead screw, surpassing the limitations of the standard stock bracket. The...

Replacement part for the CR-10 Z rod top brace. One variant holds the stock bearing. Another variant is bearing-free, in case the bearing is too tight. Another variant uses a standard 608zz or 608rs bearing. Two M3 x 14 screws are used to attach the...

I wasn't quite satisfied with the design of any CR-10 Z-braces I'd seen, and I had some carbon fiber tubes left over from other projects, so I decided to model some little mounting brackets in Blender and put them to use. You will need: M5 tap, to...

I'm replacing the stock Z motor tiny bracket on my CR-10 printer with a new one. The old bracket was holding the motor in place from the side, but since nothing was securing it from below, it kept moving around. ... This design is pretty lazy because...

This is a low-cost Z stabilizer bar kit. I had spare screws and parts lying around, which turned out to be Two (2) 2 1/4" x 3/8" screws, Two (2) 1/2" x 1/8" Self Tapping Screws 22" of 1/2" ID steel rod. That's what this kit is based on. I printed...

Just my design of a Insta360 Go camera mount for the Diatone TinaWhoop. ...Super Simple.

A guide to keep filament from rubbing on the lead screw and to help with different spool holder positions like the top mounted one in my enclosure. I printed it as oriented in the stl and with supports. It snaps on the X stepper motor and uses a...

This is a straightforward replacement component for the Z rod top bracket. It comes in three distinct versions: one that securely holds the stock bearing, another that's designed without a bearing due to tightness issues, and a third that utilizes...

... find one anywhere. ... I actually bought one and have updated it. My fin to fin spacing is off a hair, but everything else is good. https://store.micro-swiss.com/collections/all-metal-hotend-kits/products/all-metal-hotend-kit-for-cr-10-pro M2591-04

Here is the rewritten text: Creality CR-8 version 2 owners can upgrade their Z-axis support using a custom seal ball bearing adapter. This adapter requires a 23mm outer diameter, 8mm inner diameter, and 8mm thickness seal ball bearing. ...When printed...

https://www.tinymachines3d.com/collections/replacement-parts-for-creality-printers/products/z-sync-kit-1 Follow the instructions Created by Ethereal Project in this video. ... https://youtu.be/KmeYlX6eXGE I've included the Step file for anyone wanting...

I stopped by this Thingiverse post (https://www.thingiverse.com/thing:2757323) and decided to print it out for my Tevo printer myself. You can easily install it on other printers too. I printed everything with ABS plastic, making sure to use 100%...

An easy to print Z sync belt tensioner designed to work in conjunction with the original spool holder or as standalone. The parts are easy to print and they do not require supports. Hardware needed for this model is:  - M4x30 cap head/button head...

Printer box for Creality CR-10. ...First project ever.\r\nFront and Back Corner Brackets: remix from 2020 Corner Bracket by TheStapler https://www.thingiverse.com/thing:2655498\r\n\r\nSpool Holder is a modified version of Super Simple Spool Holder by...

... didn't want to let my incompetence injure my printer! ...I have a super bad habit to not pay attention to how close my z height is to falling off and destroying the carriages. ...This should stop that so I can find new and fun ways to break my printer!

I have a super bad habit of not paying attention to how close my z rail height is to falling off and destroying the carriages. This should stop that so I can find new and fun ways to break my printer! ... V2 fixes the issue with the v slot nuts being...

... The one from ssjoco is smaller at 17mm (either that or I messed up something which is quite possible)Either way I have edited the file to add the Snap Z for the Minimus and made the slot 20mm.I'll upload the 17mm wide version as well just in case.

Wheel Upgrade for the CR-10S 3D Printer The CR-10S is a highly customizable and upgradeable 3D printer that allows users to personalize their printing experience. One popular modification is upgrading the wheel of this printer, which greatly enhances...

Block for leveling the x axis (syncing Z screws), 40x40x100, print two

SV03 z sync to fix gantry problems. ... will work for other printers just follow directions

Z-Sync & Pointer Tronxy X5S with FreeCAD file It took me a long time to think about the Z-Sync problem and the issue with the first Layer of the printing. There are many solutions proposed like Z-Stop and Z-axis sync belt. Unfortunately each...

For the CR-10S5, this is a remix of the turnbuckles from the Z-brace kit by Buildituniversity. I extended the turnbuckles by +50mm and +75mm, so you can use a 24in threaded rod off the shelf, instead of buying longer rods and cutting them down to...