1 inch to olympic converter 3d models

This adapter will allow the use of standard Olympic weights on a threaded 1" barbell. ...I couldn't find a threaded version so I made my own.

Helps you to convert 30mm rings to 1 inch. ...Useful if you have existings 30mm rings and you want to install a 1" scope

This adapter was created to allow for convenient use of Olympic weight plates (2-inch hole) with Standard barbells/ equipment (1-inch bar). I designed this adapter to fit 10-45lbs plates (25-40mm adjustable range). Smaller plates can be used as well...

So give me likes, post makes, comment and rate the print to show others and me how well it goes.If you post a make, let me know which filament you use.If you want to support me by donating a coffee go to https://ko-fi.com/antimaterie I would really...

I modified it here to work with a custom fly rod holder with mounting holes that are 3" apart on center (https://www.thingiverse.com/thing:5247483 - I recommend the wide standoff version.) There is a hole through the center to mount an optional 2",...

Triceps Barbell adapter: 30mm threaded to 50mm / 2 inch Olympic **ATTENTION!!!** Double check dimensions of your barbell before printing. ...Each of these are 10 hours+ prints, and it is a tight fit for *my* barbell: My barbell screw: - 29.65 mm...

Copyright (C) 2020 Peter Senna TschudinSPDX-License-Identifier: GPL-2.0-onlyThis design is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty ofMERCHANTABILITY or FITNESS FOR A PARTICULAR...

A 2.5 inch to 3.5 inch Drive converter.    Features:               1. Cooling Slots               2. Low Profile Rails               3. ...2mm Floor and wall thickness for strength    Printed on an Anycubic I3 Mega @ .3 layer height Using...

Simple 2.5 inch to 3.5 inch SSD/HDD drive converter.   Why have simple air holes when you can have a nifty design! ... Printed on Makergeeks Pearl White Raptor PLA .2 mm Resolution.   Doesn't need rafts or supports

With this caddy you can load 2.5 inch SATA disks in a 3.5 inch hot-swap bay. Use 2.5 mm pins to anchor the disk in the caddy. ( see pictures ) The height of the 2.5 inch drive can be adjusted in the openSCAD file. The .stl file contains a version for...

... handles and barbells were 1". I originally planned to hold the bushings in with the spinlock collars that came with it, but I found that they held on just fine by themselves after I couldn't push the bushings in all the way onto the handles.

It is a converter that enables the installation of Olympic size plates 50mm on the neck in standard size 28-30mm. Converter for 5kg and 10kg plates. There are differences in the size of the plates from different manufacturers. ...Level them by scaling...

Video on these adapters Sizes for the width of the adapters are as follows .5" .75" 1" 1.5" 2" 3" 4" 5" 6" 8" 9.5" 12" If want one of these and can't print them in ABS/HIPS stop by my ETSY store...

1.5 inch to .75 inch reducer

Plate weights are expensive. ...I wanted a quick way to adapt the 1" plates I had to my bar. This simple hanger means you can leave them on your dumbbells so you have a bit less loading/unloading. ... Tested with 40#

An adapter that converts a 1/2 inch female screw to a 1/4 inch male screw. A camera etc. can be attached to the tip of the stick of the tamo net that can be extended. After making 1_2To1_4ScrewA.stl, insert the screws and cover with...

This is a eyepice converter from 2" to 1,25" for a telescope.

A converter for a 2'' eyepiece holder to a 1.25''. ... Usage described in the following video - https://www.youtube.com/watch?v=1JgXcH-ixx0

0.96" eyepiece converter to 1.25". Its advantages: it fits into standard covers, and you can also use older high-quality eyepieces for today's modern binoculars. ... Disadvantages: the ring gets stuck in the eyepiece, so it is difficult to remove it,...

A sample filament converter

This machine was built to convert (re-extrude) my 3mm fil to a 1.75mm fil. The bottom spool in this picture is an existing roll and was just placed there for demo purposes. Instructions This was made from 1" square steel tubing from the hardware...

Converts olympic size weights to fit a standard 1" dumbell or bar. The sizes are set to fit the Fitness Gear brand plates. I use the weights on an olympic bar as well so I didn't want the rings to be hard to remove. These slip in and out easily...

Simple Design used to make 30mm bar into Olympic, I have only used it stationary I am unsure how durable it would be in active use. ... Bolt will need to be used to secure the piece in place

An adapter that makes it so Olympic weights stay in place on a universal machine. The OD is 2", the ID is 1". Comes in two heights, depending on your weights download the one you need/want. ...

The end of the adapter I created with 1 inch inside, as well as outside thread. And an adapter is intended for PP fittings, on which a sealing ring is attached to the outside after the thread. I am still printing, but show you by photos what I...

http://www.thingiverse.com/apps/customizer/run?thing_id=1246651 Instructions Using the following options: SmallEndDiameter = 46 TaperLength = 25 SmallEndLength = 25 InsideStop = no LargeEndDiameter = 65 SmallEndMeasured = inside LargeEndLength = 25...

This is modeled to work with a ridgid shop vac 1 3/4 inch hose to a 1 inch hose to handle more vacuum attachments. ... 100% infil use heat to form fit after printing.

Needed some bushings for some scotch brite wheels with 1 inch holes to adapt to 1/2 inch shaft at machine shop. ...I have compensated for shrinkage.

A 45 degree Y-adapter for 1-inch schedule 40 PVC to two 1/2 inch barbed hose connector. ...I designed this for the return line on my reef tank where space was limited.

This is a small clip designed to attach an accessory with 1 inch webbing to a strap with 1.5 inch webbing, or vice versa. ...My particular use case is attaching this [awesome water bottle...