2040 extrusion 3d models

Aluminum 2040 extrusion with V-slots (ender 3).This model is available in black and silver and is drawn in Autodesk Inventor pro 2021.

2040 Extrusion corner.

2040 Extrusion corner.

2040 Extrusion Mount for 3D Chameleon.

a 5mm thick shim that matches up to 2040 extrusion

Bracket for 2040 extrusion to reduce vibrations. ...Makes printer quieter :)

This is a 100x100 VESA mount that will attach to 2040 extrusion that I threw together in Fusion 360.

This is a cap that sits on the end of a 2040 extrusion and has slots for two 13x13mm rubber feet. ... Need: 2x 13x13mm rubber feet

Another endcaps for 2040 extrusions.Press fit no screw needed. ...Printed with ColorFabb XT-CF20 &nbsp;4 perimeter 0,15mm.</p><p>Frame from Blackfrog.PL</p><p>Hope you like it</p>

DescriptionClamp for 2040 extrusion. ...Clamp can be used like holder for Articulating Raspberry Pi Camera Mount or other accessories.</p><h4><strong>Print Settings</strong></h4><p>Layer height: 0,2<br>Supports: No<br>Infill: 20%<br>Filament material:...

Toolholder for 2040 extrusion, has places for allen keys, filler for leveling,spatula for removing prints,two tweezer holder and hooks for wrenches,just snap it on the frame(may require a bit of force but it holds really firmly without dropping on...

It uses M5x10mm bolts for mounting the bottom of it (side with 4 holes) to the 2040 extrusion and M5x12mm bolts for mounting it to the 2020 extrusion (side with 2 holes). I've been printing my brackets around 80-85% infill for higher strength but...

I needed a set of feet for a 2040 extrusion to be used as a TV table stand. The feet is longer in the front to stop the TV from tipping over. It slides on (it is a tiny bit larger than 2040) and should be enough, added holes for countersunk screws if...

This is a quick and dirty 2040 extrusion shim. I added the channels for V-Slot to keep it compatible for others that might be using the d-bot parts and would have clearance issues otherwise. Print it at 100% infill, put the face of it on the bed,...

This drilling guide should help drilling 2040 extrusions across, it uses 3 625 bearings per hole, use a 5mm drill bit. To flush screws into the the the aluminum extrusion after drilling the extrusions, use a M5 steel hex screw (hardened is best)...

... it). ... This is a cable-keeper for 2040 aluminum extrusion. Use a 4mm twist-in T-nut in the non used track. Keeps the cable(s) in the other track from falling out. I made these for my laser engraver. ...I'll upload an in-use picture later today.

I needed a way to attach my 32" display to a 2040 extrusion since it did not come with any feet. The mount slides down the 2040 and is attached using M5 T-nuts. The mount holds its weight but will slide when you mount something to it. The large hole...

This is a part to mount a NEMA 17 stepper motor to the end of a 2040 extrusion rail, with the rail horizontal (for more side-to-side bed carriage stability). It has been designed to have the motor placed such that the belt can run through and over...

This is a part to mount a NEMA 17 stepper motor to the end of a 2040 extrusion rail, with the rail horizontal (for more side-to-side bed carriage stability). It has been designed to have the motor placed such that the belt can run through and over...

This is some 2040 extrusion for the AP8 made by another member, I had issues with that extrusion fitting T-nuts so i drew up some of my own. I'm printing it now so I'm not sure on the strength yet. I use 5/16" rods i bought from Home Depot for $4 to...

This drilling guide should help drilling 2040 extrusions across, it uses 3 625 bearings per hole, use a 5mm drill bit. To flush screws into the the the aluminum extrusion after drilling the extrusions, use a M5 steel hex screw (hardened is best) long...

Tablet mount offset to one side, intended for 2040 extrusion. This was designed for a tablet approx. 239 mm in length. I have included two versions:</p><p>A split version that allows for printing in parts and assembly with epoxy and screws. That's...

This is designed to fit 2040 extrusion

150mm 2040 extrusion Pla 220/60 0.3 micron

Spool holder for 2040 extrusion. ...Remixed from:http://www.thingiverse.com/thing:706504

Another 2040 extrusion endstop mount Printed in PET with a 0,6mm nozzle and 0,4mm layers

Mount for 2040 extrusion, simple box for tools, It has a compartment with a lid on the bottom. ... printed without supports.

A simple cap to cover the end of the 2040 extrusion (from 8020.com) that I used on my AM8 build

Mount for 2040 extrusion, simple box for tools, It has a compartment with a lid on the bottom. ...printed without supports.

Sligthly edited original mount with 4 holes for mounting on 2040 extrusions on Ender 3, AM8, CR10 or any other extrusion based printer. ... You can either use 4 holes or 2 holes per side.