5 gallon paint spout 3d models

End Caps for Open V-Slot 2020 with Open Hardware logo. ... This is a remix from https://www.thingiverse.com/thing:398515

Simply remove the plug from the bucket, and then push the spout into the hole until it snaps into place.Model #30669-00778https://doyleshamrock.com/product/5-gallon-pour-spout/I used the above website dimensions and provided image to make a rough...

... and buy one. ... Fits every one gallon paint can I have so far, so I suspect it will fit yours. I printed this with support which pops out really easy. Easy to press and tap on to the can, and easy to pry off. ... Enjoy and improve if you'ld like.

Attached is the spout for the 5-gallon dispenser. ...I am using PETG material for the print, however, to make it sterile with the plastics I have also mounted a safe-plastic tube inside the spout.

Opens 5 gallon paint buckets

This is a simple snap-in spout for 5 gallon plastic pails with a 50mm opening and a plain plug (not a pull-out pour spout). If you wish, you can also smear a little rubberized glue like E-6000 on the underside of the flange to form a gasket, but I...

The idea being a spout-valve combination we are all very familiar with that we can just slap on a bottle and start using once assembled. The bottle cap section is intended to be printed out of a flex filament. The rest can be printed from whatever...

Some basic Meshmixer additions; smoothed over the stress riser around where the lip of the connecting ring met the pouring spout, and cleaned up the STL with the smooth function. ...Nothing special but seems to print a bit better than without the...

A threaded screw-on spout for the 5-gallon isopropanol drum from McMaster-Carr. Several spout designs available. ...Still in testing.</p>

Gallon Can Spout

There may be a better way to turn the spout.http://www.thingiverse.com/thing:1223758 Spout for Gallon Cans It can be difficult to pour without spilling from a full gallon can. I bought a new gallon can of WD-40 and of course it's full to the brim,...

This is a rubbery cap made to fit onto the gallon spout Instructions Make this out of NijaFlex 230 degrees C print speed 30 mm/s

Washer for Gallon spout Instructions Print this out of Ninjaflex material 230 degrees C at a speed of only 30mm/s

This cap with spout allows you to cleanly and accurately pour water out of milk gallon jugs. I mix batches of water and fertilizer for my AeroGarden in those jugs and because of the large bottle mouth, pouring the mixture into the AeroGarden tank...

This cap with spout allows you to cleanly and accurately pour water out of milk gallon jugs. I mix batches of water and fertilizer for my AeroGarden in those jugs and because of the large bottle mouth, pouring the mixture into the AeroGarden tank...

This is a remix of my gallon can spout.http://www.thingiverse.com/thing:121655 This one has a spout that swivels. The spout snap-fits on to the threaded cap. The straight spout is better than nothing, but I think this curved spout has more utility. I...

So, my funnel works well but it's impossible to tip the acetone from the can without spilling it everywhere so I guess a spout is in order. If you wait or come back, I'm planning on adding some kind of lid so this can be left in-place. Other...

Since I water my plants with a gallon jug of spring water instead of a 2 liter bottle, I wanted an adapter that would fit that. Instructions Printed on an Afinia H479 oriented upside down. Avoid...

... made. ... I added a chamfer to the spout base so that you can print it without supports Instructions Print with the spout facing down, no supports. ... This will give you the smoothest surface where the can seals to the inside of the threaded area.

Edit it online https://www.tinkercad.com/things/iHptgvrAYuQ This is work in progress but I am working on making a functional 5 gallon lid opener. Test 1: I printed this out on a Makerbot 2x using the lowest quality It worked, but I suggest changing...

I used 1/2 inch screws to secure the two halves together and then a 500 mm x 5 mm diameter rod. I heated up the rod in my oven at 500 degrees F for about 20 minutes. Then carefully using hot pad mittens inserted it into the center hole. I suggest...

Just another Paint can spout. Keeps paint out of the gutter and allows more controlled pouring. ... Cheers Kisssys

Just another Paint can spout. ...Keeps paint out of the gutter and allows more controlled pouring. Cheers Kisssys Category: Hand Tools

This is an update for my quart paint can. This is nice and snug on the gallon can. Will keep the can clean and your brush. ... My original quart design; https://www.thingiverse.com/thing:2267254

I usually buy one of these at Walmart for a few dollars but they were out the other day so I printed this and glued it to my paint can lid with silicon glue. I an using it with solvent based paint so I am careful to keep the cap threads clean before...

I usually buy one of these at Walmart for a few dollars but they were out the other day so I printed this and glued it to my paint can lid with silicon glue. I an using it with solvent based paint so I am careful to keep the cap threads clean before...

This is designed to clip onto a standard gallon can of paint, and it allows you to dip the roller in and run it out a few times to spread the paint evenly on the roller and remove excess. All the excess paint then drips right back into the can, with...

Cap for norm8332's spout for 1 gallon metal can, with that you can store the spout into the can.

UPDATE: (9/10/2015) I replaced the spout with a new one that has a flat exit hole in an attempt to reduce any splashing due to gurgling. Instructions: I used PLA and it works with acetone. It did discolor but not dissolve. Some PLA contains additives...

... sand the base ring on the spout when assembling because its a tight fit. Created with Sketchup and OpenSCAD. UPDATE: (9/10/2015) I replaced the spout with a new one that has a flat exit hole in an attempt to reduce any splashing due to gurgling.