atx support 3d models
566611 3d models found related to atx support.
thingiverse
Font ATX Support Kossel Mini, I made these two supports to put the font ATX on my kossel mini. ...The supports are tightened with screws on a acrylic panel that I cutted.
thingiverse
Support for Prusa I3 Mi primer intento...... un aborto que me vale. Se puede imprimir 1 soporte de 70mm o 2 de 40mm. ... You can print 1 support of 70mm or 2 of 40mm.
cults3d
Micro ATX motherboard support, mounting on wood with 4 mm screws fixing the motherboard on the bracket with dedicated screws
thingiverse
This is made for hold an ATX PSU on a 3Drag/K8200 printer. ... Instructions Print two of this and enjoy your new ATX PSU support!
thingiverse
I need a switch for my raspberry pi power. ... for the switch, I just reuse a switch from an ATX power supply. It is fixed on a wood subwoofer box, and then, I can't make hole in it. That's why I designed this simple switch support. ...
thingiverse
I needed support for an ATX Power supply for my AM8 build that looked like the RasPi Case I printed http://www.thingiverse.com/thing:2387822 and Electronics enclosure. http://www.thingiverse.com/thing:2330654 So I mashed up this support...
thingiverse
Use these brackets to mount an HP Erica3/5 motherboard in a standard ATX case. Use one screw on the top left motherboard hole and mount three of these brackets on the bottom 3 holes of the case. ...Motherboard will side into the slot on the brackets
thingiverse
ATX power supply cover with XT60/USB/PWR_ON for Flying Bear P905 Update: 5/7/2019: Re-created with fusion 360 and added the step file This ATX power support cover has 4 XT60 connectors, a USB plug, and pin for PWR_ON and PWR_OK. The mount hole is...
thingiverse
with the 3 parts you can place the power source into a Prua i3 without any screw and very simple. Be prepared to attach your source once the printer. whether not to remove anything or screws needed Con estas 3 piezas se puede colocar la fuente de...
thingiverse
I could not find a sturdy mount for an ATX Power Supply used outside a computer case (Virtual Pinball cabinet) so I built my own.
thingiverse
permet de fixer une alimentation atx corsair cx750f sur un support via 4 vis
thingiverse
Atx power sulpply support for prusa i3. ...Required two metric 3 screws
thingiverse
ATX power supplies are way cheaper than SFX power supplies, this bracket allows support for the Cooler Master nr200 and nr200p mini-itx pc cases to be compatible with ATX PSUs...
thingiverse
This thing is taller adds material on the bottom to compensate for the proper ATX motherboard mount height. Shims will have to be printed for the ATX backplane in order to make it tall enough. I think the shims need to be 3.19mm. ...I made this for...
thingiverse
Plaque support alimentation ATX pour profils 30/30
cults3d
Micro ATX motherboard stand, with hard drive slot under motherboard wood mounting with 4 mm screws fixing the motherboard on the bracket with dedicated screws
thingiverse
A wall or case mountable stand for the ATX Breakout board. ...Raises off the ground to prevent shorting, and gives holes to mount with M3 machine screws
cults3d
Support for BeQuiet Pure Power L7 ATX power supply. ...(Or ATX with 140 x 150 x 86 dimension)
thingiverse
Support for BeQuiet Pure Power L7 ATX power supply. ...(Or ATX with 140 x 150 x 86 dimension)
thingiverse
A simple support to screw my ATX PSU under a Ikea Lack enclosure that I build. Designed to use the less material as posible. ...
cults3d
A simple support to screw my ATX PSU under a Ikea Lack enclosure that I build. ...Designed to use the less material as posible.
thingiverse
The markdown hates me, so have some raw link text to the one I used.http://www.ebay.com/itm/161040584256?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649 The PID needs 110v to it, which I used from the ATX (just got some aptly rated wire from the...
thingiverse
Nice design done by @grami_fr. I just had to rework the holes for the screws because I hadn't the right screw to fix it on my board... ... The whole PC wall mount project is available here: https://www.thingiverse.com/thing:4342844
prusaprinters
It features support for up to 2x SSD Drives or 2.5" HDD drives. You will need 6 or 8 M3 square nuts and 4 M3 Standoffs (brass or nylon is fine) for mounting the board on the case and mounting the ssd/hdd case(s) to the sides. Print instructionsSimply...