axis camera 3d models

Axis Camera

Used to mount our Axis Camera to our Robot in 2017. ...It uses a variant of the hood found on the USB Life cam mount found here: https://www.thingiverse.com/thing:1451995

This is a 3D printed mount to attach your FRC axis camera to your robot more easily which will prevent your camera from moving while you're driving. ...The camera easily attaches to 80/20 or C-channel and has 2 1/4" mounting holes spaced 2" apart.

This is a camera stand that will fit most Axis cameras. I made it to accomodate a specific camera position, where the original stand did not fit. Feel free to edit it, remix it or whatever you like. Hope you get some use out of it! ... :) Tinkercad...

This is a 3D printed mount to attach your FRC axis camera to your robot more easily which will prevent your camera from moving while you're driving. The camera easily attaches to 80/20 or C-channel and has 2 1/4" mounting holes spaced 2" apart. ...

The Axis camera is one of the web cams used in FRC. The mount that comes with the camera doesn't tighten enough so I designed and printed this for my team (3840). This could use some improvements such as tightening mechanism on the horizontal motion...

Build Video: https://youtu.be/7TkybpSQULk 3D Printed 3 Axis Camera Slider, remote controlled via Bluetooth PS3 Controller This project is based on isaac879's slider. I incorporated the pan & tilt mechanism from him. The brain is a esp32 uC with...

This is a 2 axis camera gimbal for fpv. You need two 9g Servos such as the cheap SG90. Use the servo cross or wheel to mount them to the platform. ...Use velcro or double sided tape to attach the camera to the upper servo.

This is a mount for the FRC Axis camera. Current Image is of older revision. Newer model has only one hole per side and the edge that sits against the camera is angled. ... Instructions They print fine...

This is a 2 axis camera gimbal for fpv. You need two 9g Servos such as the cheap SG90. Use the servo cross or wheel to mount them to the platform. ...Use velcro or double sided tape to attach the camera to the upper servo.

This is a 2 axis camera gimbal for fpv. You need two 9g Servos such as the cheap SG90. Use the servo cross or wheel to mount them to the platform. ...Use velcro or double sided tape to attach the camera to the upper servo.

Made this to replace some bad AXIS camera mount nuts. Used the Tinkercad isometric thread to generate the design. Printed at 0,16 mm layer height in standard PLA. This thing was made with Tinkercad. ...Edit it online...

2-Axis Camera Gimbal GoPro2https://youtu.be/Ka7nakKfFnA Controllerhttps://ru.aliexpress.com/item/Hot-2-Axis-BGC-MOS-3-0-Large-Current-Brushless-Gimbal-Controller-Board-Driver-Alexmos-Simple/32787553800.html?spm=2114.13010608.0.0.ljYDeU...

Axis serie M camera mount. Works for horizontal of vertical mount. ...Requires a standard double side camera screw (1/4-20 UNC)

Camera mount which connects to the outside of the z-axis, on the spacers. Not as big and bulky as some of the others. ...Still a work in progress, but I like it better than anything else so far.

Z Axis IR Pi CAM holder for Creality Ender 3 (Screw m3 20mm)

FAQ: http://www.thingiverse.com/shivinteger/about [>>>] Generating Attributions log: [0] Thing Title : GoPro Hero3 Frame - Improved [0] Thing URL : http://www.thingiverse.com/thing:40331 [0] Thing Author : TheCase [0] Thing Licence : Creative Commons...

2) Camera arm - allows the camera to be mounted far enough back as to not interfere with the bed and potential print area. This arm may be long enough to be used with the Ender Extender 300 kit. 3) Camera pedestal - allows the camera to be mounted...

A Camera Arm that can be controlled using an Arduino CNC Shield and uses 3 NEMA stepper motors. READ EVERYTHING BEFORE COMMITING TO A BUILD Can be configured with a variety of motors: -NEMA 17 Direct Drive -NEMA 23 Direct Drive -NEMA 17 4.16:1...

... adapter. ...Use your camera tripod for maintain your axis web camera. Works with the Screw Library http://www.thingiverse.com/thing:8793 Tested on Axis Ip Camera 207 Instructions Print without support otherwise it can block up the tripod mount hole.

Axis camera to tripod mount adapter. Use your camera tripod for maintain your axis web camera. Works with the Screw Library http://www.thingiverse.com/thing:8793 Tested on Axis Ip Camera 207 Instructions Print without support otherwise it can block...

Camera Case for FRC Axis Camera. Mounts to x-wing channel on robot using 1/4-20 screw. ...Join top and bottom halves using 1/4-20 x 1.5L screw and nut.

This model is a camera mount designed to hold the Axis camera models m1011 and 1013. ... It allows to mount on a frame to adjust the yaw and pitch to a fixed position, and can hold its position consistently with stresses from driving motion...

THIS IS FULL DETAIL OCTOCOPTER WITH 3 AXIS CAMERA MOUNT MODEL. ENJOY IT مدل کامل از یک اکتوکوپتر به همراه مانت 3 درجه آزادی دوربین. ...امیدوارم لذت ببرید

I used 2 ¼" washers on the camera screw to give enough tightness when attaching the camera.The screws came from this: Anycubic I3 Mega Z-Axis Camera Mount C920/Tripod Screw by Aerocalculus - ThingiverseBecause I used Tinkercad to modify the files I...

Found the lovely z-axis camera mount for the CR10 but wanted it on the right side, this is the result. Everything made from scratch with the left side version (https://www.thingiverse.com/thing:2516411) as guidance for the arm (spacing is slightly...

I haven't seen many Z axis camera mounts on Thingiverse, so I decided to make my own. I'm new to CAD, I just picked up the program and started tinkering. That's a full disclaimer if you want to edit this for your own uses: the Fusion 360 file may be...

Simple diamond pattern Z-Axis camera mount for the Anycubic Kobra Neo. I used the Camera Mount for Logitech C270 on 2020 Extrusion by NikNolte on Thingiverse: https://www.thingiverse.com/thing:2426231 as reference for creating the base brackets to...

This is a Z axis rising camera mount for the Duplicator i3 (Di3 Wanhao, Monoprice, Cocoon Create). This mounts a Cheap Logitech Webcam with a ZipTie (for now). It allows the camera to be out of the way but still rise smoothly with taller prints. if...

This is a Z axis rising camera mount for the Duplicator i3 (Di3 Wanhao, Monoprice, Cocoon Create). This mounts a Cheap Logitech Webcam with a ZipTie (for now). It allows the camera to be out of the way but still rise smoothly with taller prints. if...