bibo touch 2 3d models

BIBO Touch 2 Dual Extruder 3D Printer Flexion Extruder Bracket: Installing the Flexion Extruder isn’t too hard but does take a bit of extra work. All of the materials I used to make this work are from the 3D printer except for the electrical tape: -...

I modified the size of the arms so that they would latch onto the BIBO's frame. Print three arms and two of the cross braces to hold the spools. ... You can use just two to fit the cover on top as well.

This is a bracket which allows a standard 500 - 1000mw laser to be mounted to the Bibo 3D Touch 2.

This bracket mounts to the rear fan holder on a Bibo 3D Touch 2 and can hold a 6.5 mm diameter z-probe. ... EDIT: The 'bigger' z-probe is designed for the LJ18A3-8-Z/BX inductive probe

Swivel bracket for the Front and Rear Cooling Fans for the BIBO touch2 printer, so you can add a more directional airflow, The brackets are a direct replacement for the cooling fan mounts and use the same nut and bolts to secure, The Fan holder is...

These are feet for the Bibo 2 touch. The front right has slots for 3 memory cards and a power switch (16mm hole), which i've used to turn the lights off. There is also cut outs to have foam feet underneath to stop vibrations. 10mm High Density Foam...

Adjustable feet for the Bibo 2 Touch 3D printer. Uses threaded padded feet that you can buy on Amazon inserted through the holes to allow the whole 3D printer to be levelled and adds some sound dampening. Based on the original design by...

Bibo 2 touch - handle for front door. ... It´s a replacment part for the original heavy handle.

### This is a replacement X Carriage Plate for the BIBO 2 Touch. I am not sure about others, but on my printer, the one that comes from the factory has started bending and distorting. I could not find a replacement online, therefore I made one. ...I...

Low profile bed clamps for the Bibo 2 Touch's heated build plate. Uses some of the original build plate screws to attach them to the plate. But you may need to buy one or two more spring and screw sets for the back corners as these clamps are...

This is for users of the Bibo 2. It will allow for laser focus adjustment with less risk of injury. I have fitted this onto my laser module but I have not tested it in action. ... ALWAYS USE CAUTION WHEN WORKING WITH LASERS!

An upgraded print head assembly for the BIBO 2 Touch Dual 3D printer using E3D's Hemera extruders, including an improved part cooling fan shroud and a BLTouch bed levelling probe mount. If using two Hemera extruders with neither of them mirrored,...

I wanted an awesome way to mount my Pi camera on the z-axis without having to modify the BIBO in any way. There are 4 rectangle holes in the back of the support plate. I popped on Tinkercad and plugged in the measurements which all happened to be to...

This is a clamp for the Bibo2 X-Belt (2 required). The factory clamp looks insufficient and a pain to install. This clamp has the GT2 profile for improved holding, and holds M3 nuts for simplicity in mounting. ...

<p>Ersetzt die Sadwitchplatten.<br>gibt somit mehr Sicht auf die Nozzle ;)</p>

This is my attempt for a hinge for the front door. It has magnets mounted in the hinge to keep the door fully open. The magnets are 8mm x 2mm neodymium off ebay. The bolts are 20mm M4 allen bolts and m4 lock nuts. There is also a 32mm M4 bolt for the...

This is my attempt for a hinge for the front door. It has magnets mounted in the hinge to keep the door fully open. The magnets are 8mm x 2mm neodymium off ebay. The bolts are 20mm M4 allen bolts and m4 lock nuts. There is also a 32mm M4 bolt for...

I had some problems with filament that teared when the extruders went back and forth. As a solution I designed this filament guide that fits on the extruder and can be clipped on with the kind of clip you use to clip the glass to the plate. ...It makes...

Video of mounting and unmounting: https://youtu.be/357-c9S6oTw Video of ultraslim version clearing Z bearings: https://youtu.be/TpePELwAtHQ This is my take on a 5015 blower mount and duct for the BIBO 2 Touch. It is remixed from the referenced BIBO...

Y & Z axis stepper motor damper mounts for the Bibo 2 Touch 3D printer. Allows proper positioning of the motors when a stepper damper is attached to them. Based on the original design by Hackschnitzel. ... Parts List - Printed Parts: 1x Y...

This is a bracket that will connect to the corner of the BIBO 2 Touch printer. It is designed to be used with "Articulating Raspberry Pi Camera Mount for Prusa MK3 and MK2." I used 2 of the enclosure mounting holes and replaced the original screws...

A simple remix of a bed clamp modified for the BIBO 2 Touch glass bed. The blower I liked hit the stock simple clamps the BIBO came with and I could not find one low enough profile to fit under the blower. The blower in question:...

Not sure if or when they will be available, but I found this one: http://www.amazon.com/Endoscope-Pancellent-Waterproof-Borescope-Inspection/dp/B01MR8EONS/ref=sr_1_2_sspa?ie=UTF8&qid=1522673250&sr=8-2-spons&keywords=amicool+usb+endoscope&psc=1 It...

Edit it online https://www.tinkercad.com/things/bHZwU9TTyEm I designed this hinge to solve the problem of the BIBO's door constantly flapping down while working on things. It is nearly identical in looks to the original hinge, but this one does away...

This is a remix from https://www.thingiverse.com/thing:398515 I printed the original and had fitment issues with it rubbing on the rod and hitting the back mounting hardware. I modified it to clear the bar and hardware. the lower plate also made...

This is a small part to fill the hole in the power connection panel on the back of the printer that is left when you remove that switch (ie when moving the power switch to the front of the printer)

This is a remix of https://www.thingiverse.com/thing:1350343 I've been wanting to do this with one of my BIBO Touch 3D printers. I modified the original to take into account the narrower spacing on the smooth rods. I also split it into two parts and...

Replacement extruder top plate for the BIBO Touch 3D printer. This design removes the two bolts/nuts that press against the front extruder fans causing fan noise and/or fan failure. A support has been added between the two long bolts to allow these...

I created this two years ago because our BIBO Touch machines have a design flaw. The X carriage platform rides on four bearings supported by an aluminum sandwich piece that usually come broken from the factory. These four covers fully replace those...

I created this two years ago because our BIBO Touch machines have a design flaw. The X carriage platform rides on four bearings supported by an aluminum sandwich piece that usually come broken from the factory. These four covers fully replace those...