bowflex selecttech 552 series 1 replacement part disk 3 3d models
1741809 3d models found related to bowflex selecttech 552 series 1 replacement part disk 3.thingiverse
This is reverse engineered from a Bowflex SelectTech Dumbell. The Disk is the one labelled "3". ...I printed this disk in ABS and it has been working well for about a year now.
thingiverse
I broke three discs on my Bowflex Selecttech 552 Series 2 (White Numbers) dumbbell accidentally. I saw how much the replacements for these discs cost, so I decided to make my own. I printed these disc with PLA, but of course they'll be more durable...
thingiverse
Bough a set of Bowflex SelectTech 552 Dumbbells since the gym was closed during the pandemic. Great dumbbells for an apartment but our space is limited and my wife can not pick them up to put them away each time she wants to use them or to hide them...
cults3d
Bough a set of Bowflex SelectTech 552 Dumbbells since the gym was closed during the pandemic. Great dumbbells for an apartment but our space is limited and my wife can not pick them up to put them away each time she wants to use them or to hide them...
thingiverse
BowFlex 552 FIrst Generation 5-52.5lb dumbbells (red numbers on dial). These discs were made from photos of the discs. ...They are labeled properly on files but i neglected to properly label them inside the SW files
thingiverse
... Mount fits snugly into the hex holes so I had to very gently tap it flush with a small hammer. The thin "slits" are for a flat screw driver in case the mount needs removed/replaced/whatever. ...Learned that the hard way in the first revision.
thingiverse
I was gifted a broken set of bowflex selecttech 552 dumbells and I couldn't find any other designs that would actually work. The other two versions of these disks on Thingiverse caused excessive resistance when trying to adjust the weights. I just...
thingiverse
Printed successfully with ONYX on a Markforged Mark Two. ...This part supports some weight, so be cautious - make sure the material/process you use is strong enough for the job.
thingiverse
https://youtu.be/mb6xCadXje8 I created these parts because I was not completely satisfied with the amount of adjustment on my Bow-flex 3.1 bench. I have tested 3D print strength in the past, and with a lesser infill, an ABS print can handle beyond...
thingiverse
Simple replacement for foam roller end cap, compatible with Bowflex 3.1-5.1 benches
thingiverse
My off brand 1090 dumbbells end caps keep falling off so I made these. ...Just uploading because someone on reddit asked for the file
grabcad
modified part to fit my model (543-552-1), original: MITUTOYO-543-551E by Chee Kai Yeong can be found at 3D-Contentcentral
thingiverse
Replace those worn out Bowflex power bands with 2 AC servos. Greater strength range than power bands, plus the motors dont wear out.. ... early project, will update as I progress fits keyed 19mm AC Servo output shaft I am using a 750w AC Servo...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=739573 Instructions Using the following options: font_narrow_widen = 0 bar_length_trim = 0 inner_margin_width = 1 border_thickness = 3.6 whichextruder = monochrome lug_text_distance = 2...
thingiverse
part is a tested replacement part for a square 1 edge face. ...this part works and is fully functional.
thingiverse
A replacement part for the original QiYi Square-1. ...Designed in Solidworks.
thingiverse
HESH 3 headphone replacement part. Support material easy to remove. Keep screws at least 6. ... Be careful when disassembling the headphone.
thingiverse
www.endlessobjects.com Print Settings Printer Brand: Ultimaker Printer: Ultimaker 2 Rafts: No Supports: No Resolution: 0.1 Infill: 85-100 Notes: If you use Slic3r you can create a modifier model and only make the middle part of the headband 100%...
thingiverse
this is wave one of custom or simular parts to the coasterdynamix lego parts. ...more on the way
cults3d
Very specific replacement part, I have the "GE Café™ Series 28.6 Cu. Ft. French-Door Refrigerator" Model: CFE29TSDSS Over time the door engaging plastic piece at the top of the refrigerator was getting worn down and would not engage the door seal.
thingiverse
Very specific replacement part, I have the "GE Café™ Series 28.6 Cu. Ft. French-Door Refrigerator" Model: CFE29TSDSS Over time the door engaging plastic piece at the top of the refrigerator was getting worn down and would not engage the door seal....
thingiverse
This is the replacement for the disk used for holding tablets for kids in cars. It plugs in the air vents. The kids don't guess the way to take off the magnet and pull until the plastic disk breaks. Probably designed to break, the original. Attached...
pinshape
Summary Very specific replacement part, I have the "GE Café™ Series 28.6 Cu. Ft. French-Door Refrigerator" Model: CFE29TSDSS Over time the door engaging plastic piece at the top of the refrigerator was getting worn down and would not engage the door...