coolling 3d models

motor coolling fan

75 Ton

cooling sistem anet a8 soon other info

Prototype to hold a micro Dragon link and transmitter

A simple 12 cm cooling fan support. It fit perfectly in a 128X150 mm emplacement. ( 3 X 5" 1/4 Bay ). The fixing claw are 12mm long. It could be tweaked to goes in your old ugly PC boxe. The optionnal bee grid is 0.45 mm So maintain a high temp bed....

Liquid cooling system Thermotron 730SBM-01

Modify E3D Fan Mount for 3mm cooling fan , add support on Blower Fan . Angle can be adjustable. No support needed. ...Blower Fan I use ADDA AB4512HX-GD0 , data sheet in here :http://www.adda.com.tw/data/file/AB4510.pdfUpdate Improve the AB4512HX Mount...

Modify E3D Fan Mount for 3mm cooling fan , add support on Blower Fan . Angle can be adjustable. No support needed. ...Blower Fan I use ADDA AB4512HX-GD0 , data sheet in here :http://www.adda.com.tw/data/file/AB4510.pdfUpdate Improve the AB4512HX Mount...

CLH - Single Channel 200W, High Power Driver

use for coolling

E3D coolling fun duct with two air flow for powerfull 60mm fan. ... Instructions Print it with fan foles laing down.

It is for coolling step driver tmc2208 for trigorilla board with 4010 fan for my printer anycubic kossel plus

A Coolling tunnel for driver with a 40x40 fan. ...it is for the SKR Pro 1.1 You need the spacer 2 times 03.12.2019: v2 Added with a round inlet for fan

Had a hard time lighting up my Lotus wood burning stove. ...So I designed a mount for a pc coolling fan, to get some ekstra air flow, when starting a fire.

There is a place for the fixing of original fan (extruder cooling) and a 50x50x10mm fan for printed parts coolling. You'll need 2 M3*35 screw for fixing the parts on the printer and 4 more screw+bolt M3 for nozzle's level fan cooling. ...News : 40x40...

A Coolling tunnel for driver with a 40x40 fan. it is for the SKR Pro 1.1 You need the spacer 2 times 03.12.2019: v2 Added with a round inlet for fan Do you like my work? ...then Support me https://www.paypal.me/raabi1991/

I did make a light fan duct (just 36 gram) for better coolling for the motor end ESC. I just extended the duct to to fit all electronics to. I hate do tight op the cabes, zo this way you can't see my messy wiring. ...

... three LM6 linear ball bearing - upper 2, lower 1. ... Motor mount for bowden extruder motor - using nut for space to easy mount to maintenance. Coolling fan duct is not included - I printed one of uploaded cooing fan duct in Thingiverse for V6 hotend.

A Coolling tunnel for drivers with a 40x40 fan. it is for the SKR 1.3 the desing was made for a tronxy x5sa case and will fit in this case https://www.thingiverse.com/thing:3808742 you can see it at the pictures they will also work without the case...

A Coolling tunnel for drivers with a 40x40 fan. it is for the SKR 1.3 & 1.4 the desing was made for a tronxy x5sa case and will fit in this case https://www.thingiverse.com/thing:3808742 you can see it at the pictures they will also work...

remix of the Tronxy X5SA board case by Clooney i use this case because i have made a coolling tunnel for the skr which fits exactly (look at the picture withe tunnel) i have add a second hole at one holder for my pro groundplate the one cable hole is...

remix of the Tronxy X5SA board case by Clooney i use this case because i have made a coolling tunnel for the skr which fits exactly (look at the picture withe tunnel) i have add a second hole at one holder for my pro groundplate the one cable hole is...

and if you have a prusa A8, or a clone prusa i3 the fan is exactli at the rigth height to help coolling the X axis motor. include some spacer so you can plase the cables behind the board and have nice cable manage. ... all the holes in the case are...

The Cobra - Rear mounted cooler for Wanhao Duplicator i3 is a very nice, stylish and efficient coolling pipe (much more efficient than the asthmatic original one). Another advantage, we can see the nozzle from the front. But the distribution PCB on...

... I used hatchbox PLA, black, 190C coolling from 2nd layer up was at 100%. I initial had my temperature set to 195C and cooling at 80% but my first print curled up at the corners. ...How I Designed This I used 123D Design and Simplify3d to print.

Do not let it cooll down : immediately screw it afer the ens of the print, so that it takes the correct form. 2 small screws are needed to maitain he screw on the bottle cap. Disclaimer : be carefull : test the stability before you leave your...

Most of the air flow will go to the hot end, while the rest will be channeled to the nozzle for the print coolling. Use a fan with enough airflow as it will work as two fans in this case. if you have any issue to make the duct fit your hot end...

two fans one for nozzle radiator and second for print coolling adjustable ,removable and replaceable fan ducts all cables can be fit inside, so it looks clean has hole for cable and bowden covering elastic pipe easy cover removal for maintenance can...

I liked that it uses 2 screw points to mount and a 5015 fan for part coolling. Also, the fan housing blocks a lot of the air from the heatsink fan from blowing down on the print area which helps prevent over cooling when printing PETG, ABS, and the...

-I strongly advise you to usePETG or abs not sure pla could hold its rigidity in time passed. -Also keep coolling off or max %30 for better layer stickness. -While printing the Parts place just like in the pictures and choose infill pattern cubic or...