electrical tape roll holder 3d models

Electrical tape holder Extending from 50mm to 90mm Inner tape dia 36mm

Electrical tape holder for hanging tape on the outside of your kit.

This is my custom design of an electrical tape holder for belt or tool pouch. this works with "3m vinyl electrical tape 37", I haven't tried any other tapes of brands. tape belt clip v5 has an experimental zip tie holder. ... let me know what you...

This is just a little call mount clip for a roll of electrical tape. ...It has a couple of screw holes to you can mount it to a wall.

This is just a little call mount clip for a roll of electrical tape. It has a couple of screw holes to you can mount it to a wall. ...

Needed something to put my excess rolls of electrical tape and see what colours I have as well. Able to be printed without supports. 02-06-18 - V2 Added a little lip on the bottom incase someone wants to mount in their vehicle and it shouldn't...

Hold your electrical tape with ease! ... use .8mm nozzle for a quick print

<p>I rotated the print back side down and let it print. ...I made this because I use several different colors of electrical tape and wanted something to organize them and make them easier to access.

Simple Electricaltapeholder. ... 10 Rolls 12.5 mm wide slots Outside size 45*152mm

Designed a tape holder for holding rolls of tape for rod building. ... These are designed to hold two rolls of tape up to 1" in width.

This thing is made to replace the roll bearing in a Tesa Tape holder.

This is a simple holder for a Tape Roll. You simply need to screw it to a vertical surface. ... You can use it for other purposes obviously.

Roll holder for 25.5 mm (diameter) tape rolls. I adjusted it a bit and made the two sticks on the side a bit thicker and shorter to fit the needs of this particular tape dispenser. The sticks are 5 mm long and 7.8 mm thick. ...In total it's 33,5 mm...

After having printed a bunch of tape roll holders by ctheroux ( https://www.thingiverse.com/thing:295690 ), I needed something to hold smaller rolls also. So I designed a simple holder, based loosely on ctheroux's design. ... .sldpart (SolidWorks...

This is a simple holder for a Tape Roll. You simply need to screw it to a vertical surface. ...You can use it for other purposes obviously.</p>

My blue tape roll was always getting in the way so I got out one of these spool holders from my scrap bucket and repurposed it. As shown in one of the photos, this arm can hold a roll of tape up to 3 inches wide. I use a two inch wide roll for my...

You can use 1x big roll, or even 2x small rolls next to eachother (example: if you need different colors) HOW TO: 1st option: Add 7 strong magnets (10x4mm) in the clip and holder. Alternate the + and - (see picture)! Glue the caps on top. Now you can...

This is a simple holder for a Tape Roll. This design is much more robust than the previous one (http://www.thingiverse.com/thing:154458). You simply need to screw it to a vertical surface. ...You can use it for other purposes obviously.

This is a simple holder for a Tape Roll. This design is much more robust than the previous one (<a href="https://www.thingiverse.com/thing:154458">http://www.thingiverse.com/thing:154458</a>).</p><p>You simply need to screw it to a vertical surface.

A hook I made to store all my different tape rolls. There's a smaller one and one that's a bit longer. ...You can screw it on the wall or just put some double sided tape on it.

I'm constantly picking this roll of tape up and moving it around, so I thought I'd give it a better home, and designed this holder. The first draft of the design was sort of a fixed bar that just went straight out. I didn't even bother printing...

Replacement tape dispenser spinny center piece. Works for standard rolls. I split the model and print in two halves then superglue together. ... Made in both PETG and PLA Roughly 16 minutes to print, about $0.20 of plastic.

I use blue painters tape on a glass bed for all of my printing and I wanted some place to put the roll of tape so it would be out of the way. This has 2 slot for the arms to hold the 1" and 2" rolls. Arms are super glued in and in my case are able to...

A replacement part for that little thing in tape dispensers that the roll of tape is held on. Instructions There are two files. They are the same but just a different orientation. ...Personally, I think...

Replacement for Scotch and similar size tape dispensers. ... We lost one in our office, and rather than buy a new one it was easy enough to design and print. Can print in 1 piece with supports, or as separate holder and pin, then glue them together.

... ID of tape reals, meaning it haves to flex to fit inside, does so pretty easily, and will not shift at all! Hope it helps someone else who has had the same occur, such to throw out such a heavy tape dispenser just because of a little plastic pin!

... that mounts to walls. ...This will work with standard sized rolls of adhesive tape, such as masking tape, painters tape, packing tape, duct tape, Gorilla tape, etc. Print without supports. ...Secure with one 1/2" or 3/4" #8 or #10 countersunk screw.

This is a simple electrical tape holder for 25mm (1 inch) wide belts. I should be suitable also for backpacks with MOLLE System. For reference mine is a Stanley Fatmax 1-95-611. I reccomend to print it with PETG for more flexibility and resistance...

This is a simple electrical tape holder for 25mm (1 inch) wide belts. I should be suitable also with backpacks with MOLLE System. For reference mine is a Stanley Fatmax 1-95-611.<br>I reccomend to print it with PETG for more flexibility and...

Wall mounted tape roll holder with BLUE or DUCK cover. ...This is designed to be printed as 2 pieces and glues together.