emco compact 5 lathe parts 3d models
1041059 3d models found related to emco compact 5 lathe parts.thingiverse
3D-printed change gears for EMCO Compact 5 lathe EMCO compact 5 feed mechanism comes with 6 change gears (for common metric threads): 20, 25, 50 and 3x 60 teeth For uncommon threads or imperial threads additional change gears are needed: 26, 30, 34,...
grabcad
Small Austrian lathe I'm working on, to retrofit with new electronics and Mach3.
thingiverse
These are parts that I used to add an electronic leadscrew to my Emco Compact 10 lathe. They may also work on the Emco Super 11. They mount a NEMA24 stepper under the headstock and controls and an optical encoder onto the geartrain. The Stepper...
thingiverse
Set of holders for EMCO Compact 5 lathe Most holders are for original accessories and tools, some of them are not, like the quick change post toolholders and live center, see the pictures. Print these holders in the position like I uploaded, as...
thingiverse
This is a control panel for Emco Compact 5 after motor and VFD upgrade. I could go with much smaller switches, but I wanted a real authentic feeling switch, the switch is actually overkill for a VFD. In the pictures you don't see the new motor...
thingiverse
A chip guard for Emco Compact 5 lathe Disclaimer: I won't take any responsibility if you damage your machine or burn your machine down when you are using this thing. Use common sense when using it. This guard keeps the way cleaner, and the chips...
thingiverse
... covers in place. Simply print two of each length and cleaning up your lathe will be faster next time. They may be useful for other lathe’s as well. I attached the design files so you can change them to your needs. ... https://a360.co/3mWcUBt
thingiverse
Gear set for Emco compact 10 lathe. ... Gear profile: MOD 1,0 Height: 10mm Bore:19mm
thingiverse
Aerowerk created a new button for the EMCO V10 lathe that was a simple push fit. https://www.thingiverse.com/thing:4687444 However the original buttons had an offset wider hole to accommodate a small curved steel spring to hold the button firmly in...
thingiverse
i designed those gears in fusion 360 with this addon: https://apps.autodesk.com/FUSION/en/Detail/Index?id=6294804001663532834&appLang=en&os=Win64 Module = 1 Tooth Profile: Ix1 DIN3972
thingiverse
The dril column on a EMCO Compact 8 Lathe can be used as a router tool. To measure the depth of the router bit I use a dial gauche. I have made a holder fo this gauche. It is fastened to the dril tool by a short M6 wire rod and nut in an existing...
thingiverse
There are radio buttons for an old Maximat V10 lathe. The original plastic buttons get brittle from age and break. The steel button actuators are hard to press without the buttons. The originals had a little spring piece to take up space in a...
thingiverse
Small cones for turning small objects in a lathe. Instructions Was made on Rep. 2: High, Infill 100, Shells 3, Layer height .15, Temp 225, Speed w/ext. 80, Speed w/trav. ...150.
prusaprinters
Two of the change gears in the thread-cutting / feed gearbox on our Emco Maximat Super11 lathe at Stockholm Makerspace had broken teeth after a crash, and spares were very hard to get, so I designed and printed these change gears.They were printed...
thingiverse
One that replicates the original design, with the EMCO logo and perimeter trim embossed on relief, on the outer surface and one with the outer surface totally flat, with a low relief logo, for easier printing. Besides, the inner brackets have been...
thingiverse
Customized version of https://www.thingiverse.com/thing:2682637 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2682637
thingiverse
These are for larger lathes than the Unimat and introduce their own problems, but if action is taken to mitigate these (see below) then this unit works admirably well on a tiny lathe. Having bought the boring head for a larger lathe (Myford ML7), I...
thingiverse
Soft jaws for a 2.5" vise. ...These are on an Emco machine vise. ...No magnets or anything, just use double sided tape under the horizontal lip on top or a bit of super glue or something else to hold them on, if you want to use something.
grabcad
Here are the entire parts of the lathe tail stock and in the next upload i am going to upload the assembly Lathe Tail stock Assembly(IGES and Solidworks part)
thingiverse
All Mini Lathe parts I printed with PETG at 100% infill. ... The Tool holder was printed with PETG at 15% infill.
grabcad
This parts catcher is used in multiple models of Okuma lathes. ... They get beat up so terrible, need to reproduce them every so often.
thingiverse
Parts for Moseley lathe, or other WW/watchmakers lathe. Printed in abs and filed to fit. The tail stock should be bored out on the lathe it will be attached to. the basic dimensions of lathe bed are included in picture, please note i did not make the...
thingiverse
After printing out alot of the parts from the gingery lathe thing from sprocket1597, I saw that alot of the parts were missing, so I started designing the parts in freecad so I could get all of the parts to build the full lathe. Im still missing the...
grabcad
lathe tail strock.barrelcenterfeatherhand wheelkeynutscrewspindlespindle bearinglathe tail strock Assembly coming soon.
thingiverse
I worked on making a wood lathe and need to print out bearing blocks and a pulley.