ender 5 control board 3d models

As you can see from the power supply mount, i went for the BTT skr E3 Turbo board, which isnt a direct rteplacement for the creality board that came with the printer. So after moving the power supply, i really need some better way of cooling it. ...

This Front panel is designed for those who want to use the beautiful control board holder made for Ender-3 (https://www.thingiverse.com/thing:3352127) on your Ender-5 or Ender-5 Pro machine. The problem was that Ender-5 metal plate won't fit in the...

... case. Works great for using Klipper on a Raspberry Pi, Creality Sonic Pad, or anything else running Klipper. There is also an adapter for the Heated bed control board. It shifts it over and down so the leads from the control board are long enough.

The Ender_5 control Box offers mounting for the MeanWell_LRS_350_24 Power Supply, Mainboard controller, Fan, LCD, and an optional shelf for TL Smoothers, while at the same time utilising all the stock hardware. ... 12 hour print time (THERES...

Designed from scratch using Fusion360, but Highly inspired by the creality Ender-3 ButtonBox from Matereo, and using the same switch size. This is my first design so I used it to learn Fusion. ...

Main board used in Anet 3D printers. ...Can be used to layout your own electronics enclosure for your own machine.Two versions will be available - (Basic) and (Full) to fit in your PC performance.

You can find my own control box design for Ender 5 plus. ...Feel free to make modifications :) Suggestion: 0.24mm, PETG

I needed a bracket to move my control box to the rear of the Ender 5.The M5 24-40mm was close but I needed more wiggle room. So remixed the M% 24-40mm bracket and made it slotted. ...This allowed the left and right movement needed to mount the...

I remixed the holders for the ender 5 control box. The originals would take about 6 hours per part to print. I made models that should only take about 3 hours( per side, so 6 hours in total for left and right) to print. They might block a small...

I searched for a better solution and found the Ender 5 Control Box Bracket by rgrugan. I printed these out and mounted them and they worked. I still had the problem of wanting to include my Raspberry pi and EZABL control box inside the original...

Simple external control board mount and housing for the ender 3. Cable tube requires a 25mm hole and is the right length for an IKEA Lack table. Its a little bit loose but this allows for a bit of error when drilling the hole. ... Items Required: 4 x...

Based on the amazing kilroy01 Control Panel Back Cover. Just added some fancy venting holes and the Creality Logo. To avoid the light bleeding I suggest to add some electrical tape in the back of the logo. <b>EDIT:</b> In the V2 was added...

I wanted a control board fan cover for my Ender 3 so I designed this one in Fusion 360. It is based on my bat and crescent moon logo whilst trying accounting for machine movement around it as well as maintaining a good flow of air and trying to...

Both adapters did not fit my needs. I had the same problem as timmeyb, that the power supply was too long, additionally I wanted to keep the fan inside the electronics enclosure, next to the heatsinks. Optionally you can use a small screw, to secure...

I kept the overall design of the adapter, what I changed is that I remade everything in OpenSCAD and moved the mounting of the board itself further back. ... Everyone can modify the offset by them self inside the .scad file, to put the board further in...

Heated bed control block found inside the Ender 5 Plus. ...Does not include all components, and the heat sink isn't visually accurate (but the external dimensions are correct)

This is the cover for the Ender 5 control panel. The cover is mounted using stock screws. Soon after I successfully tored off by ocasion some SMD resistor from that panel (luckily I've managed to found the replacement and solder it), I've...

After 6 months of using the Ender 5 Plus with the original control box removed, I am happy with the results. It is so easy to access all of the components and it makes the wiring much easier to manage and change. New pictures added of current...

Nothing special, just another Ender 5 Pro control box cover with ventilation slots. Printed in PETG because it was the only green filament I had on hand. :) All edges where the screen ribbon cable routes from the enclosure are rounded to prevent...

This mount can be used to put the Control Box of the Ender 5 to the rear of the printer. It fixes the issue of short cables and makes the mainboard accessible without flipping the printer over. Downside is the bad accessibility of the SD Card and a...

I wanted to put my Raspberry Pi 4B within the Ender 5's Control Box for a contained relocation of all the brains to a cooler area when I move my CE5 into an enclosure. I added this https://www.thingiverse.com/thing:4140386 and wanted a clean way...

I searched for a better solution and found the Ender 5 Control Box Bracket by rgrugan. I printed these out and mounted them and they worked. I still had the problem of wanting to include my Raspberry pi and EZABL control box inside the original...

------------------------------------------- Wanted to move the control box to stand vertically at the back of the printer, so I could use the under space for storage, and also give slack to the wires to upgrade to the SKR V1.3 without extending...

I wanted to move my screen to an upright at the front on my ender 5, and needed a cover that would interfere with the ribbon cable, so adapted this to suit, original ribbon goes in the back. ... I have never done any editing etc so if someone can fill...

My remix of the Ender 5 contol panel back cover I liked the design, but after a print I thought it felt a bit unnecessary bulky, so I took measurements of the printed part and made a new one from scratch and made it a bit thinner and also with vents....

This is just a quick back cover that I threw together for my Ender-5. Printed upright with no supports. edit - I have had a few people that comment that the tolerances are too tight on this. It was designed to the printer that I have and slides...

Inspired by Ender 3 full PCB cover with drawers by Doc_Martin.

simple quick adapter plate to mount the skr v1.3 control board in the ender 3 original location.

I first created an enclosure for the control panel and then realized it's a great place to hold some of my longer tools since it's elevated. So I pushed the back out and made slots for my pliers, scissors, brushes, scrapers and my Dremel knockoff.

This is a cover to protect the exposed PCB on the Creality Emder 5 3D printer. It fits securely using the 4 screws attaching the PCB to the panel. It incorporates a handy tray at the rear, and a cover for the ribbon cable. It's designed to print with...