kite string for tie dye 3d models
2304817 3d models found related to kite string for tie dye.thingiverse
for tying up tie dye patterns (or whatever else). The bit on the top is a tamp/probe for tamping the fabric or to open pleats. Make sure to print it at 80-100% infill to make it as strong as can be. Layer height is 0.2mm or 200 microns. I also...
cults3d
Reel for flying line or kite. ... Video of printing and assembly: https://www.tiktok.com/@betta3d/video/7142512365723143430
thingiverse
It took a little less than an hour to print the scoop and the medium size tip only, but the medium tip was to large and dispersed the dye to quickly so i printed the small tip and it's perfect for what i need and screwed on perfectly. I am printing...
thingiverse
A nozzle that can be glued to the caps of most plastic bottles. ... I used it for tie dye pigments, however it has plenty of other uses. ... Print settings: 0.25mm 100% infill No support No raft
thingiverse
Created for u/blackfixie on reddit. ...Hopefully it can serve as a learning tool for Fusion 360 as well.
cults3d
Created for u/blackfixie on reddit. ...Hopefully it can serve as a learning tool for Fusion 360 as well.
cults3d
You can tie the kite string to this, and then switch the clip between kites. I recommend printing in ABS at 100% infill. No supports needed. You may need to sand a bit to fit your kite's string hole. Not flight tested yet. ... Update: Simplified...
thingiverse
You can tie the kite string to this, and then switch the clip between kites. I recommend printing in ABS at 100% infill. No supports needed. You may need to sand a bit to fit your kite's string hole. Not flight tested yet. Uses and includes my...
thingiverse
Cutl line of wooden pieces for Shibori These are cut lines of Itajime Shibori, which has been a kind of "Arimatsu Narumi Shibori", a typical Japanese tie-dying technique for 400 years. Cloth tied with wooden pieces on two sides dies in a bucket...
thingiverse
Should help reduce the tedium of winding the kite string back on the small string holders that come with children's kites. I added a version 1.1 to stiffen up the sides. After I wound up the string with some good kite tension on the line the sides...
thingiverse
This is another “string winder” to wind and manage the line for flying a kite. Most designs I have seen were too small for my taste. That is why I made my own design. ...
thingiverse
Printable kite string spool Designed to be printed with support everywhere. 10% in a concentric pattern works well and is easy to remove. ... Holds at least 500ft of light kite string
prusaprinters
This is another “string winder” to wind and manage the line for flying a kite.Most designs I have seen were too small for my taste. That is why I made my own design.</p><p><a href="https://www.buymeacoffee.com/AoO2SOds2Q">Of course you are completely...
thingiverse
For winding sections of nylon filament into 2 or 3 separate coils in preparation for colouring it with fabric dye. The winder handles spin on 6mm (1/4"?) coach bolts held in place with an embedded nut and one prong of the winder is attached with a...
thingiverse
Wanted a kite string reel that you could print without supports. The handle is not really needed but is fun and makes it slightly faster to reel in the string. I can only get a finger or two in the handle or my thumb. My kids can get most of there...
thingiverse
This is intended to be printed in two parts and then glued together. ... The spool is fairly large and not intended for small kites with thin line. ... Pictured on the spool is 500ft of 200lb line.
prusaprinters
Print as many as you need, we will print 4 to support 1 large t-shirt.This helps keep the colors from pooling together as we wait for the colors to set, hope you enjoy this model :)There are 3 pieces in the file, print the below for 1 setQty 1...
thingiverse
I couldn't find a good way to secure the string to my head, so I designed up these cord locks. Use 1/2-2/3 of a spring harvested from a ball point pen and it should provide plenty of tension to keep your mask on your head. ... Stay safe out there...
thingiverse
EDIT I added a new string holder that's got a string position retainer (holds string when deployed) Original I made this because I find it a pain to have to wind up kite strings (or any string really). This should allow you to save some significant...
thingiverse
Place the internal remnant (in the case of the 150mm piece, it'll be the circle with all the little cross-braces cut out of it; for the 200mm piece, it will be a ring about about 5mm thick) inside the hole. This will help hold the cross-braces in...
thingiverse
2014年9月13日に行われた「有松絞り×デジタルファブリケーション・ワークショップ」で、板締め絞りのための版木をデザインすることから手ぬぐいを制作しました。蛇腹に折りたたまれた布を版木で挟むことで染料が中に浸透することを防ぎパターンを生み出す、板締め絞りという技法です。 協力:Maker Lab Nagoya、久野染工場 Instructions Process Video https://vimeo.com/108547896 How to make it 0) Download...
thingiverse
2014年9月20日に行われた「有松絞り×デジタルファブリケーション・ワークショップ」で、板締め絞りのための版木をデザインすることから手ぬぐいを制作しました。蛇腹に折りたたまれた布を版木で挟むことで染料が中に浸透することを防ぎパターンを生み出す、板締め絞りという技法です。 協力:Fablab Kitakagaya Instructions Process Video https://vimeo.com/108547896 How to make it 0) Download cut-line...
thingiverse
There are some downsides of a classical way of tying a string: * you have to do something about string ends; otherwise they can scratch the soundboard or your hand * extra length of the string loop contributes to the string settlement time *...
thingiverse
An optimized version Guitar String Tie Bead. ...Tested on my classical guitar.
thingiverse
These things are great for tying beadless strings like those on a classical or flamenco guitar. They allow you to tie the strings off away from the bridge, saving yourself some dents and scratches. I don't recommend PLA for this. Nylon works great,...
thingiverse
This is a small coupler for easy coupling of a small kite to a line, use a loop on both sides and go through the holes, around the shaft and over the pole. This will couple the two loops. I have had succes with it, i hope you will have succes...
thingiverse
Print hot and slow for the most clear part. ...then you may need to file the tracks for detents and o-ring Printing first clear now.
thingiverse
Customized version of http://www.thingiverse.com/thing:45576 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=45576 Instructions Using the following options:...
prusaprinters
<p>This was just a quick design to help grow my modeling skills.</p>