lightsaber flashlight 3d models
10407 3d models found related to lightsaber flashlight.
thingiverse
Yoda lightsaber with space for a flashlight battery pack, a button, an led, and wires. ...Pieces should just snap together.
thingiverse
__Flashlight in format of Star Wars - Jedi Lightsaber.__ Easy to print and mount. New version(more space for electronics). You do not need to print the tip and blade, they are optional. Print how many blades you want. 1, 2 or 3 RGB LEDs,...
pinshape
Flashlight in format of Star Wars - Jedi Lightsaber. Made in OpenSCAD you can change all. Easy to print and mount. You do not need to print the tip and blade, they are optional. Print how many blades you want. 1, 2 or 3 RGB LEDs, more LEDs more...
thingiverse
This is a lightsaber made to screw together and hold a generic rechargeable LED flashlight inside it. Also made to have a magnetic belt attachment. If I get a chance, I'm going to try to make the shorter one too. Modeled in Fusion360. 1) The...
grabcad
-Original Design-Two Halves + LED + Button Battery. ...(CR2032- 3 Volts)-The light saber has a push button system that presses on the LED wire and makes contact with the button battery, making it light up.-Approximately 5 inches long and 1 inch in...
thingiverse
Multiple remixed ends that can be screwed onto the Collapsing Lightsaber (Removable Blade)" by 3DPRINTINGWORLD that allows a $4 torch to light up the blade. I have created some new saber bodies that work with the blades so search for my other...
myminifactory
I used an thin flashlight (https://www.amazon.com/dp/B072K27MCK?ref_=cm_sw_r_cp_ud_dp_2EYEQGB05M27KGX1EXYX) and also used an acrylic rod for the blade. The rod is made specifically to better defuse light to the outside and not just the two ends like...
thingiverse
After doing the remix for the OLight ($15) I wanted a cheaper alternative, and I found these at 4 for $15 on amazon: https://www.amazon.com/dp/B0195L3D80/ref=twister_B07ZTX739B?_encoding=UTF8&psc=1&coliid=I2FYLH0Y80NPOG&colid=126JPHIC04RJA And $5 for...
thingiverse
Very small and short, but put this on a small flashlight (mine was a 25.85mm diameter), and it makes a passable lightsaber for a kid.
thingiverse
Change the flashlight in a Jedi lightsaber. I use a cheap flashlight purchased on aliexpress. The diameter of the mounting ring of the 41mm and the length of the sword (without a flashlight) is about 31cm. ...Print it as a vase.
cults3d
Change the flashlight in a Jedi lightsaber. I use a cheap flashlight purchased on aliexpress. The diameter of the mounting ring of the 41mm and the length of the sword (without a flashlight) is about 31cm. ...Print it as a vase.
thingiverse
This is a mini Lightsaber made to look as close to Obi-wan's as possible while still fitting on a Harbor Freight flashlight. The translucent "beam" looks pretty good at night. The 3 pieces of the hilt should be printed in grey or silver. They will...
prusaprinters
A bit of epoxy putty put mine back together with no subsequent problems.The largest collapsing blade segment actually sits on the rim of the flashlight cap with this design, which makes it protrude a couple of millimeters forward of the end. I was...
thingiverse
The largest collapsing blade segment actually sits on the rim of the flashlight cap with this design, which makes it protrude a couple of millimeters forward of the end. I was too lazy to fix the file (sorry) but after installing my "bladelock"...
thingiverse
A rechargeable flashlight cap, to be used with 3dprintingworld's [Collapsing Lightsaber (Removable Blade)](https://www.thingiverse.com/thing:3606120). The light automatically switches on when drawing the blade. FreeCAD source included. Also...
prusaprinters
A rechargeable flashlight cap, to be used with 3dprintingworld's Collapsing Lightsaber (Removable Blade). The light automatically switches on when drawing the blade. Also needed: – Subminiature Microswitch (TS0101F020P) – YAGE Mini LED Flashlight...
thingiverse
The other version: [Flashlight mod for the Collapsing Lightsaber](https://www.thingiverse.com/thing:3733269) A rechargeable flashlight cap, to be used with 3dprintingworld's [Collapsing Sith Lightsaber (Removable...
prusaprinters
A rechargeable flashlight cap, to be used with 3dprintingworld's Collapsing Sith Lightsaber (Removable Blade).The light automatically switches on when drawing the blade.To bring balance to the force I made this version for the Sith Lightsaber.Also...
thingiverse
Alternate enclosure for Prospect3DLab's Matchstick flashllight. I added a switch between the positive lead of the capacitor and the LED driver. Switch is part number JS202011CQN https://www.digikey.com/products/en?keywords=JS202011CQN ...