makerstoolworks 3d models
23 3d models found related to makerstoolworks.thingiverse
Mekada design of Vaporeon - added thin pedestal support to help improve adhesion during printing. ...Print Settings Printer Brand: RepRap Printer: MandelMax 2.0 - makerstoolworks How I Designed This FreeCAD
thingiverse
The goal is for the TAZ to accept these screws: http://store.makerstoolworks.com/motion/z-axis-lead-screws-and-nuts-set-of-2/ This has not been tested as I don't have the parts yet. ... You will want to buy 5x6.35mm couplers:...
thingiverse
... I will no longer support what they do in any way. ... If you were looking for one of the things I made you might be able to find them on my website http://captain-slow.dk/ or on MakersToolWorks's new site http://share.makerstoolworks.com/physibles
thingiverse
Every parts cooler I could find didn't quite work with my E3D setup, so I made my own! ...Be sure to use ABS or other high temp filament - it gets hot down there. Print Settings Printer: MakersToolWorks Rafts: Yes Supports: Doesn't Matter
thingiverse
Instructions Parts I used these parts from Makers Tool Works: http://store.makerstoolworks.com/motion/z-axis-lead-screw-and-nut-single/ http://store.makerstoolworks.com/motion/helical-shaft-couplers-set-of-2/...
thingiverse
The Hub file is a insert that fits into the center of the Makerstoolworks filament spool and rides on the Pin that goes across the two uprights. Its simple and works well. Instructions Since this...
thingiverse
... Instructions Just print and attached to the side rail with M5-10 screws and T nuts. Use Post Install T nuts so you don't need to disassemble. http://store.makerstoolworks.com/hardware/t-slot-nuts-post-install/
thingiverse
... here. One is for use with a blddk-style hobbed sleeve, and the other for a standard hobbed bolt. Both are sized for 1.75mm filament. Here's a link to the blddk-style sleeve: http://store.makerstoolworks.com/extruders-and-parts/machined-hobb/
thingiverse
... need to disassemble. http://store.makerstoolworks.com/hardware/t-slot-nuts-post-install/ For the camera, a standard 1/4-20 screw or bolt should be all you need. ... I used a slightly longer screw with a nut on it so it is easier to hand tighten.
thingiverse
Uses eight SDP self aligning bushings, available from Stock Drive Products (For example http://shop.sdp-si.com/catalog/product/?id=A_7Z41MPSB10M, also available from http://store.makerstoolworks.com). Four in the idler end for the anti-binding...
thingiverse
it's angled to line up with the Y belt anchor bracket for either the trinitylabs or makerstoolworks Y rails, but should also work on other projects. As there really isn't much plastic for your anchor bolts to bite into for the Y switch mount...
prusaprinters
For that reason I am specifically NOT including the firmware instructions here, though you can probably find them in the build thread somewhere. Build thread: https://forum.lulzbot.com/viewtopic.php?f=16&t=2134&p=12802 Picture of it in...
prusaprinters
it's angled to line up with the Y belt anchor bracket for either the trinitylabs or makerstoolworks Y rails, but should also work on other projects. As there really isn't much plastic for your anchor bolts to bite into for the Y switch mount itself,...
youmagine
Makes Tool Works sells a small 40mm fan that you can find here: http://store.makerstoolworks.com/electronics/blower-fan-24v-40x40x20mm/. This is a blow fan, so it supplies a very good supply of air. I created a mount that allows you to use either one...
thingiverse
... else out there is still using one of these old rigs and can get some use out of my designs. https://store.makerstoolworks.com/collections/frontpage/products/lead-screw-with-bronze-nut-for-all-mtw-printers https://www.thingiverse.com/thing:217274
thingiverse
... You should be able to use the pictures as a reference to how the prints go together. Once you secure the top plate, the pieces will keep the RX antennas and VTX/antenna secure. Print Settings Printer: MakersToolWorks MiniMax Rafts: No Supports: No
thingiverse
Build thread: https://forum.lulzbot.com/viewtopic.php?f=16&t=2134&p=12802 Picture of it in operation: https://www.youtube.com/watch?v=huuQKAljBeghttps://youtu.be/xQqZEzUxSpg Link to get the electronics:...
thingiverse
Print Settings Printer Brand: RepRap Printer: MandelMax 2.0 - makerstoolworks Supports: Yes Resolution: 0.4 mm Infill: yes, 30% Notes: Used FreeCAD, Slic3R and Pronterface Post-Printing Instructions requires few screws to attach...
thingiverse
Instructions Makes Tool Works sells a small 40mm fan that you can find here: http://store.makerstoolworks.com/electronics/blower-fan-24v-40x40x20mm/. This is a blow fan, so it supplies a very good supply of air. I created a mount that allows you to...
thingiverse
Hardware needed: (8) 3x10mm screws (I used hex head) (2) 3mm nuts (backing plate to mounting rail) (2) 3/16 x 1 inch pan-head screws with wing nuts and washers (2) [M3 T-Slot Nuts, Post...
thingiverse
;) Instructions Follow the MM2.0 hardware assembly instructions found here:http://www.makerstoolworks.com/support-and-docs/assembly-guides/ substituting your printed parts for the laser-cut versions as you go along! (Dont forget to accomodate for any...
thingiverse
... 1x 625zz bearing (5x16x5mm) 1x Nema17 gear reduced motor http://store.makerstoolworks.com/extruders-and-parts/geared-nema17-stepper-motor/ 1x m3x20mm bolt (socket head cap) 1x m3 nut 1x m3 washer (flat) 2x m3x10mm bolt (socket head cap) 1x 8mm I.D.
thingiverse
Components & Materials: -20mm Aluminum Extrusion from Misumi -90 deg Brackets from Misumi -M5 & M3 screws from Misumi -1/4" MDF from Home Depot -Glass plate from Home Depot -3D printer filament for custom parts -LM10UU & LM8UU Bearings from Robotdigg...