microphone clamp 3d models
52098 3d models found related to microphone clamp.thingiverse
Fits for example an SM58 microphone and similar models, and has a 3/8" inside thread for mounting it to a microphone stand. Requires an M6x25 internal hex screw with corresponding nut (see https://www.thingiverse.com/thing:2518438). In contrast to...
thingiverse
Needed a way to mount my microphone closer to me without buying an arm. ...Remixed a desk headphone holder and removed that and presto , desk mic clamp! ...
thingiverse
These files are for the clamp in my HD650 microphone project. The two sides are connected with screws for plastic (no room for knurled nuts, the screws dig into the plastic) The boom arm (flexible shaft from a USB LED light) is held with a M3 set...
thingiverse
https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...
thingiverse
... holder. The top and bottom clamps are the same but I've kept them as unique items as it will probably go through multiple iterations. ... (yes the files are name using the incorrect spelling of Mic, I'm currently concussed and will sort it later)
thingiverse
... fitting for the Sennheiser MZQ 800, MZQ1, ... ...clamps. It already includes the thread in 3/8". Required tools: * Drill bit 8mm After printing gently clean the clamping screw holes with drill bit by hand to make them fit the sleeved screw firmly.
sketchfab
Bauhaus-Universität Weimar // Topology Optimisation WS16/17 // Ronny Haberer
thingiverse
If like me, you have a 2cm thick vertical wooden plank on the side of your desk, you could be interested by this design : It's a clamp that holds the microphone stand in place and allow to fold its feets. Finally, more room for your wheelchair ! ...
thingiverse
This is an adapter to mount a boom onto a microphone stand. There are 3 pieces, the part for the vertical stand, the part that mounts on the boom, and a ring that keeps them together but allows rotation of the boom. There is no need for screws,...
thingiverse
**Description:** My sister's MicroKorg XL microphone broke just at the top of the gooseneck. I made this clamp as a quick repair. It requires a lot of tension, so I printed it in PETG. Stiffer filaments like PLA may break. I designed it in...
prusaprinters
If you broke your clamp system or i you have ann ikea table that can't support he original clamping this one should work, You sould print it on the side and with 40% infill for the rigidity, it shhould hold the clamping force (don't over tight it or...
thingiverse
Post-style mic clip I made that attaches to the bottom half of a standard mic clip. ...The plug in the center of the attachment hole is made for easy support removal.
thingiverse
Print using Standard Quality (0.2mm layer height) settings with an infill of 15-20% for the threads to come out fully defined. ...Let me know if this was helpful.
thingiverse
pare clamp for microphone stand Hier ist eine Ersatz Druckplatte für den Mikrofon-ständer von Millinium. Leider war die original Platte viel zu schwach konstruiert, das diese schon nach kurzer Zeit brach. Ich habe mit Sketchup eine stabilere...
thingiverse
After breaking the joint of my boom arm microphone stand, I decided to try my hand at designing one. I looked to some available products for inspiration and used the hardware from the old one. The diameter for both tubes is 5/8", the bolt appears...
thingiverse
A simple clamp to prevent the the RODE PSA1 microphone studio arm from swinging out while not in use.
thingiverse
... column of my monitor stand. ... The vertical tube is 36mm in diameter so I made this clamp-on holder to fit. You will need two #10 screws and nuts to make this work. ... I printed this in PETG with 4-5 perimeters to make the holes stronger.
thingiverse
This is a desk shelf for clamping light arms and microphone arms. My desk did not have a good mount point for the clamp which I why I designed this. Since this will be something that is clamped on you will want to print this around 50% infill. ...
cults3d
This is a desk shelf for clamping light arms and microphone arms. My desk did not have a good mount point for the clamp which I why I designed this. Since this will be something that is clamped on you will want to print this around 50% infill.
prusaprinters
The vertical tube is 36mm in diameter so I made this clamp-on holder to fit. You will need two #10 screws and nuts to make this work. I printed this in PETG with 4-5 perimeters to make the holes stronger. Print instructionsI printed this at 30%...
thingiverse
... if it fits on other flashers or camera's so we can other users. Best is to print this part laying flat at your print bed (ring down, shoe vertical up) Because of the strength the clamping ring needs. Placed supports as needed. ...(i needed a few)
thingiverse
Basic clamp to use with a microphone boom or stand. Sized to a 16mm diameter pole. Print Settings Printer Brand: MakerGear Printer: ...
thingiverse
This was originally designed as a microphone holder on a podium. I decided to make it customizable so that it can be used to hold anything round in the center of a round hole. ... Open it in the customizer to adjust the dimensions.
thingiverse
This is a cable-clamp, that I've designed for Schoeps microphone cables.
thingiverse
### Type A Normal clamp to hold cables in place on microphone stands ### Type B Clamp without the hole for cables. Can be used to drill other items onto it. ### Type C Same as type A, different height (smaller) ### Type D Clamp with a larger hole...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_captive_protruding_h = 0.5 gopro_bar_screw_head_d = 6.3 gopro_rod_nut_od = 8.05 gopro_secondary_what = clamp gopro_bar_screw_nut_d = 6.1...