otf blades 3d models

a better blade for the otf knife

NOTE: i have a fully designed and working utility blade compatible blade for the OTF knife as well! ive designed it fully and it works superbly well (ive designed it for gerber blades but im pretty certain it would work with any standard "scalpel"...

Only a rubberband is needed.The screws are optional but recommendet.

Once the blade slide freely, put the outer blade top over it (to enclose the inner blade) with some spare rubber band secure the two outer blade part together (that would lock the inner blade inside the outer blade) and be sure that the inner blade...

A middle finger instead of a knife

was bored at work.. remixed this baby... gonna print it out for a coworker to use as a letter opener.. ...:D

Updated to parts for OTF Knife / Switch Blade (Functional) by David6722 https://www.thingiverse.com/thing:3619717 Update 4/3/20 added the Top case, by request. I made the blade double sided and gave it more of a "dagger" shape. It gives the blade...

THIS IS NOT A FINISHED MODEL This hidden blade I made in Inventor is fully working when the right tollerances are used, when printing this yourself you have to try to scale the models down or up by a bit. I cannot assure you this model will work...

These are a couple more blades for [David6722](http://www.thingiverse.com/David6722)'s [OTF (out-the-front) switchblade](http://www.thingiverse.com/thing:3619717). You can add some swagger to your carry with a Bowie or tanto blade. (But not too...

One [more](https://www.thingiverse.com/thing:4096221) blade for [David6722](http://www.thingiverse.com/David6722)'s [OTF switchblade](http://www.thingiverse.com/thing:3619717). This one is based on the [Microtech](http://microtechknives.com)...

I really liked this blade style, but it's for the pen-spring mechanism version of this knife which I've had no luck with whatsoever, however I've had small successes with the elastic band mechanism version of this knife and as such I wanted to...

Just a comb blade, for the amazing switch blade made by David6722, all credit goes to him! this file has all the pieces needed at the correct scaling. ...you may need to cut it to separate the individual pieces, if needed

If you succeed, please share your photos. ... If you like it very much, please leave a message.

Improved top case from OTF Knife / Switch Blade, which strengthens the side tab above the button, so it is attached by more than one layer to the side case (@ x1000 scale), and not prone to breaking off as on the original. Modified original file...

I took David6722's genious OTF Design and tweaked it a bit, I added places for screws, a pocket clip, altered the button and made a few more improvements. Prints very easily but may need some supports on the newly created overhangs. Print at 1000%,...

I took David6722's genious OTF Design and tweaked it a bit, I added places for screws, a pocket clip, altered the button and made a few more improvements. Prints very easily but may need some supports on the newly created overhangs. Print at...

You really just need a rubber / hair band and a couple of small screws (or tape / glue instead)Category: Mechanical Toys SummaryI took David6722's genious OTF Design and tweaked it a bit, I added places for screws, a pocket clip, altered the button...

... to make some simple changes to make them work together again. ... I recommend printing the blade vertically on its spine with supports. Original OTF: https://www.thingiverse.com/thing:5180916 Hellhound blade: https://www.thingiverse.com/thing:4097691

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/54QEWptaEQU

i made a sharp blade and the button on the switch so it is easier to use DISCLAIMER DO NOT USE THIS IN ANY WAY SHAPE OR FORM TO DO ANY THING HARMFUL TO ANY ONE OR ANY THING!!! ...ALL CREDIT GOES TO DAVINICI85 UPDATE 4/23/2016: Do NOT use the blade that...

It is a 3 d printable otf blade. use two rubber bands and print 100% infill. ABS Or PLA. Play may break easily. ...like Share follow

OTF

otf

otf krambit knife. Print 100% infill. PLA or ABS. ...like share follow

... anything stupid like modifying it to have a real blade. OTF switchblades are illegal in several states. Additionally be aware that schools etc have pretty much a zero tolerance policy for anything even remotely looking like a weapon. ...Be smart.

Please also note my other designs on the subject of slingshots: https://www.thingiverse.com/thing:3087021 Edit 11.11.2018 Here is a nice Video on Youtube, showing the print and shoot of the Slingshot OTF (https://youtu.be/2UOXk_c8ftM) thanks to...

Remix of davici85's design. ...I made the blade into a comb, rounded off the corners, and added better texture to the switch. ...I'll probably upgrade this further in the future to make it more streamlined.

OTF chain pendant novelty

Clip for otf pen

Blades.....