tektronix oscilloscope knobs 3d models
33490 3d models found related to tektronix oscilloscope knobs.thingiverse
Knobs for Tektronix 24XX series oscilloscopes. Both smooth and notched versions. ...To maintain good quality on visible surfaces, I recomend printing in this orientation, and then removing the support from inside with a pair of tweezers.
thingiverse
This is a model for the knobs on a Tektronix Oscilloscope. Me and my Engineering Student colleagues have ahem misplaced a few of our oscilloscope knobs over the years, so I modeled them in order to have INFINITE KNOBS! Anyone that has an oscilloscope...
thingiverse
There are two knobs attached: A longer knob designed to replace any channel's "Variable" knob named "variable" in the attached files. A shorter knob designed to replace the "Sweep Variable" knob named "variable sweep" in the attached files. Print...
thingiverse
This knob may be used in place of either channels position knob, the trace step knob, the horizontal coarse and fine positions, trigger level, and holdoff. Since I was missing two knobs, I actually opted to print the knob in both yellow and blue. ...
thingiverse
Oscilloscope multifunction knob, for analog channel sensitivity selector on a Tektronix 2213 , 60 MHz scope. ...Printed upright, at 40% infill.
thingiverse
Small knob for tektronix oscilloscope TDS 2002B. ...Four original small knobs are easy to destroy during many years of usage (especially when device is stored inside of cabinet after each use).
thingiverse
Simple Knob for Tektronix TDS 210 Vertical and Horizontal positions and trigger potentiometer
thingiverse
replacement button for tektronix oscilloscope (in my case 2220 model)
thingiverse
Rear foot that holds power cord on Tektronix 453 oscilloscope. ...My original feet got old and were crumbling apart.
grabcad
Here is a model of the TDS2000 Tektronix oscilloscope for people who wants to add some electronical instruments in their presentation. ...It is very Basic, just for the look...
thingiverse
Foot for Tektronix 310 / 310A oscilloscope. Original foot is smooth black. Can be complemented with a 7/16" rubber ball (original ball is blue). ...Updated: Increased inner diameter as the fit was a bit tight.
thingiverse
Foot for Tektronix 465 oscilloscope (as well as other models). I designed this as a temporary measure to stop my scope with a missing foot from wobbling. I plan to add the little bumps to hold the power cable in place. ...Ideally needs to be printed...
thingiverse
This is a replacement part for the cordwrap feet on a Tektronix 453 oscilloscope. The original feet on my oscilloscope had deteriorated and no longer held the power cord in place. I made this part from measurements taken from the original part and...
thingiverse
Replacement feet for Tektronix TDS874 oscilloscope. ...Will most likely also fit on TDS500 or TDS700 series.
thingiverse
Tektronix TDS-1002 Digital Oscilloscope - it is used to look at and measure electronic signals on a voltage and time scale.
cgtrader
Tektronix 2235 Oscilloscope 3D model. This model comes with an oscilloscope with powered ON and powered OFF textures. Modeled in Maya and textured with Substance Painter and Photoshop. The model is built to scale and is UV unwrapped with 4k Textures....
thingiverse
This is a 3D-printable replacement rear panel for a Tektronix 2225 CRT oscilloscope. If your scope, like mine, is missing its original plastic rear panel, this will provide: * Rear feet. Rubber stick-on feet (≤ 14 mm diameter) can be inserted. *...
thingiverse
Connects a Tektronix TDP3500 active differential probe to a PCBite arm. ... Insert an M4 nut at the bottom.
thingiverse
so i designed some legs for my 465B Oscilloscope and i had one good leg to do it from. ...the part is as accurate as i could get it using fusion 360.
thingiverse
I Own and Restore many old TEKTRONIX Analog scopes and when using them in bright light situations, the trace is often not visible due to many factors, such as bright overhead lights or sunlight. This CRT shield or shade eliminates much of the glare...
thingiverse
If you lost the power button cap on your oscilloscope, you can now make another one ! The model is parametric. You will probably need to adjust the hole size, because it is extremely tight so that it can be press-fit in place, and the precise value...
prusaprinters
<p>Printed in standard PLA with low layer height (0.8mm height took 1 hour) and 55% infill. Tight fit. ...Print two so they match!</p>
thingiverse
Replacement pan/zoom knobs for a Tektronix DPO 4050 scope. Mine was missing these and after a little bit of work i got it working great. ... Solidworks part files and STEP files included if you want to modify them!
thingiverse
This is a collection of various knobs that I came up with to replace ones that were damaged or missing from Tek 7000 series scope plug-ins and mainframes. Most of these assume that one has the original knurled aluminum piece with the set screws that...
thingiverse
It should fit many other TEK equipmentstoo - I think they are fairely standard for those generation of TEK equipment. Print at small layer height like 0.14mm for best quality I print them with 1mm wall thickness, 1mm top-bottom thickness,...
thingiverse
Knob for older tektronix 7000 series and possibly other scopes. It requires the original metal insert. To apply the aluminium insert, remove the screw, heat the insert up with a soldering iron and push it inside like a standard heat insert. This...
thingiverse
hey, the feet of my beloved tek osci 465 fell apart. so here's a simple new design, which let's you still wrap the power cable around like in the original. I just left out the separators for the cable as they are not really of any use. I...