water bottle with sleeve 3d models

Water System Bottle Sleeve

With this 3d printed sleeve you can easily tell your water bottle from everyone else's. Accepts 500ml bottles, i'm using a water bottle bought from Costco here (Kirkland brand). Simply break the seal on the new water bottle then unscrew the bottom...

At work we all have the same company water bottles. Great free, not so great they all look the same. So I made this to make mine stand out. I have made multiple ones. I had made (not photoed) that I had to use my slicer to join as it was to complex...

The Voss water bottle itself measures at 71.27mm using digital calipers. The sleeve fits tightly around bottle. Sleeve is 80mm in length, and is printed vertically for maximum build quality. It takes 3 sleeve sections to cover exterior of bottle....

Prototype sleeve for Voss 375mL bottle. The sleeve is a very basic cylinder created in Blender. Exterior diameter is 58.0mm, interior diameter is 57.5mm. The sleeve fits tightly around bottle. Sleeve is 150m in length, and is printed vertically for...

I love Zephyrhills water, but the plastic is so thin and the bottoms are often wobbly and malformed, so I designed this sleeve to fit the 16.9 oz sized water bottles. No more crackling water bottle when you you pick it up and it feels good in your...

I created this textured grip for the Pura Stainless Steel water bottle. (http://www.purastainless.com/) While the current grip made of silicone is just fine if you have a normal grip but if you are like my son who has low tone and does not have a...

I always keep bottles of water in my car, and the 500mL bottles I prefer tilt in the Tesla's cup holder. While the concept is trivial (it's a cylinder with a gap), it did take some consideration to make it work well. More detail can be found [on my...

WATER BOTTLE RENDERING

My dad wanted a handle for his free water bottle, so I came up with a sleeve that fits around the lid and bottle, add some paracord through the handle and tie it at the little loops. It slips around the lid lock in the front which still fully works,...

Transparent plastic bottle with a screw-on cap and half filled with water. ...Aligned screw thread between bottle and cap with no interference.

simple Water Bottle With its Mold Used By Generative Shape Design of CATIA V5 R21 Rendering With KeyShot 4

This is a Water bottle with a cap that is fully customizable for you or can be printed as is.

This file can be used to print a water bottle with a hole in the bottom for the filter (included in design). The filter and bottom of the bottle is then covered by another piece that seals the filter inside of the bottle and provides stability to the...

IEOR 170

WATER BOTTLE with cooling structure

This is Water Pump with Bottle 3D model

This is a water bottle with fruit container

This is the water bottle with filter functions by Solidworks2016.

Customized version of https://www.thingiverse.com/thing:99020 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=99020

A simple water bottle designed using FreeCAD

Designed a water bottle with proper outer boundary grip styling and made its cap also which is at the top.

Converts four plastic bottles in a tank of water up to 8 liters. ..., The distance between the rings is 9 cm, compatible with all PET bottles. ...Above each ring there is a small tube that allows air to escape.

Converts four plastic bottles in a tank of water up to 8 liters. ..., The distance between the rings is 9 cm, compatible with all PET bottles. ...Above each ring there is a small tube that allows air to escape.

I use this to pour my silica beads into the water bottle after reconditioning them. It has not been tested with anything liquid. I printed mine with a resolution of 0.2 for the funnel part and 0.1 for the threaded part with the funnel side down on...

2015 cause bottle challenge entry. ...This bottle features a rugged design with a screw on cap that can also work as a cup.

1 litre plastic bottle.

Funnel with lids to store pre-workout. ... Not water tight, but should hold powder.

It has a canal, which can be mounted under the mount, to catch the rest of the liquids from the bottles. There is also a parametric holder for the bottle caps. The models can be changed in fusion 360. The Screw holes are made for 3.5mm Woodscrews....

WATER BOTTLE with inner metallic coating