1 4 hex to 1 4 square 3d models
2744280 3d models found related to 1 4 hex to 1 4 square.grabcad
1" long steel adapter for 1/4" hex drivers. ...Ball detent secures 1/4" socket with square mounting shank.
grabcad
2" long steel adapter with 1/4" power drive hex (quick release dog end). ...Ball detent secures 1/4" socket with square mounting shank.
thingiverse
If you have a screwdriver handle for hex bits and want to attach a tool with a 1/4" square fitting then this adapter may be for you. Instructions The one I use myself are printed with nylon and...
thingiverse
Specs : 1/4"(6.35mm) Hex compatible Description : 1/4"(6.35mm) Hex to 1/4" Square adapter With this toolhead, you'll be able to use any 1/4" square bits that you probably have lying around. This is just a tool head. If you need a handle or other...
grabcad
2-3/4" long steel adapter for 1/4" hex drivers. ...Ball detent secures 1/2" socket with square mounting shank.
grabcad
2" long steel adapter for 1/4" hex drivers. ...Ball detent secures 3/8" socket with square mounting shank.
thingiverse
Used to attach a hex socket to a cordless drill. ... Not for high torque applications.
thingiverse
This adapter enables you to use a 1/2" square nut on a 1/4" square socket wrench. ...Print at 100% infill and the smallest resolution possible to ensure a precise fit and maximum strength.
thingiverse
A simple 1/4" hex to 1/4" socket adapter, you have to force it in the first time.
thingiverse
This adapts a 1/4 inch carriage bolt to fit in the hex cutout on the stands leg locking bolt
cults3d
This adapts a 1/4 inch carriage bolt to fit in the hex cutout on the stands leg locking bolt
thingiverse
... knife. If you'd like a more snug fit, or you want to adapt it to a size other than 1/4" hex, just scale the whole model up appropriately -- remember, Quadrant Drive doesn't care how big it is, it will mate just fine with any other Quadrant Drive.
thingiverse
I bought an electric screwdriver to more easily work on my 3D printershttps://www.amazon.com/HAMMERHEAD-Rechargeable-Screwdriver-Patented-Technology/dp/B00S8D0ICG However, it didn't come with all allen bits and the bits I have don't fit (5/32" vs...
thingiverse
make sure you use a brim to keep it adhered to your print bed. Keep in mind, don't expect this to handle too much torque or it will snap. If you find it isn't strong enough, you could try to print it on it's side but I have no idea if it will...
cults3d
make sure you use a brim to keep it adhered to your print bed. Keep in mind, don't expect this to handle too much torque or it will snap. If you find it isn't strong enough, you could try to print it on it's side but I have no idea if it will...
cults3d
... hex bits. ...These fit loosely in the 1/4" hex bit holes. I designed a small spacer to fill the gap and make it look nicer. Now I have a nice holder to store all my spare bits. Here is my Hex Bit Holder on Thingiverse: 1/4" Hex Bit Holder/Organizer.
thingiverse
The marking on this set is in inches (hence : 3/4, 5/16...) Sizes : 1/4" - 5/16" - 3/8" - 7/16" - 1/2" - 9/16" - 5/8" - 11/16" - 3/4" Estimated Print time @ 70mm/s : single bit : from 1 to 5 mn small set (1/4" to 1/2") : 15 mn big set (9/16" to 3/4")...
thingiverse
... I designed a small spacer to fill the gap and make it look nicer. Now I have a nice holder to store all my spare bits. Here is my Hex Bit Holder on Thingiverse: [1/4" Hex Bit Holder/Organizer.](https://www.thingiverse.com/thing:4877428/ "Title")
cults3d
... ball bearing capture type chuck. ... 1/4" hex shaft to 1/4" hex socket adaptor for 1/4" hex magnetic capture type shaft to 1/4" square pin convertor. 1/4" hex socket will have a slight tight fit for the 1/4" hex shaft convertor. ... For light load job
prusaprinters
Now I have a nice holder to store all my spare bits.Here is my Hex Bit Holder on Prusaprinter:1/4" Hex Bit Holder/Organizer.Print SettingsPrinter Brand:Prusa Printer: I3 MK3SRafts: No Supports: NoResolution: .2 Infill: 100%Filament:Duramic 3D PLA...
thingiverse
My use for this was to attach a low scale inch pound torque wrench with 1/4" square drive to a large socket needed for a yoke nut. This will allow me to set bearing preload (less than 10 in/lbs) with a more convienent tool setup than a stack of...
thingiverse
This adapter works best when made on an SLA printer, but it should work on others. ...It is not meant to be used with a power tool, just handtool adapter. Note: The 1/4 inch side is meant to be very tight, while the 1/8 inch end is loose.
thingiverse
I have a super cheapy cheap Black and Decker drill (like [this](https://www.amazon.ca/Black-Decker-71-792c-Alkaline-Drill/dp/B0093C7TZA)) and I want to drive a socket with a 1/2" drive, This adapts one to the other. I tried printing the "pretty"...
thingiverse
Schrauben lockern Mit Akkuschrauber rausdrehen / reindrehen I have designed and printed the "hexagon to 1/2 inch" adapter to be able to carry out the wheel change on my car with the cordless screwdriver without having to buy an adapter. Depending on...
thingiverse
Hexagon socket adaptor to 1/4" square. Different sizes from 7-20 mm. Not recommended for screws that need high torque. The hex-shape width is 0.15 mm bigger so that standard nuts and bolts can fit. I only tried PLA, maybe other materials are...
thingiverse
Bit adapter that has a standard 1/4" (6.31 mm) shaft that goes to a pentagonal (nominal 5 mm side length). 11 May 2017: I messed up the hex dimensions. They've been fixed with updated SLDPRT & STL files. ... 13 May 2017: It was too big on the hex...
thingiverse
This part is very scale tolerant so you can scale the part for a different fit of the 1/4" hex anywhere from being a loose fit to rigidly fixed to the part. When I print this in PLA, the hex is a slip fit. When I print it in ABS, it is a nice...