1 4 inch screw 3d models
1299193 3d models found related to 1 4 inch screw.thingiverse
Printable 1/4" (quarter inch) screw, like used for typical camera mounts. Marked work-in-progress because the square base is very uncomfortable for the fingers, and the printability is not ideal. On my PrintrBot Simple wooden, worked best when...
thingiverse
Just a very basic insta360 handle, couldn't find one so I remixed the https://www.thingiverse.com/thing:2686278 in prusaslicer To improve strength of the screw, just print it horizontally with supports. ...
thingiverse
... (small) camera... al the parts are 3d printed.... this is version 2, version one had several issues. The only remark is that you have to put some non slippery surface on the bed... The second file is just a screw, i designed to test the thread.
thingiverse
This is a replacement piece for the Neewer Light Panel to allow it to accept a 1/4 inch screw. This replaces the stock mount that comes with the panel. I lost my mount so I decided to make one that is more modular then the stock piece. ...Use the...
thingiverse
Just a simple spacer for offsetting a bracket from a wall. ...I needed a 3-inch long spacer for securing some shelves to the wall. Biggest spacer at the hardware store was 1 inch. Diameter of this spacer is 0.65". ...Hole size is 0.262".
prusaprinters
Just the single screw I designed because I needed it for this project:Lens Cap HolderUpdate (01-07-2020): Edited a new version to be printed lying on the print bed: Camera Screw V2Update (19-04-2022): I uploaded some longer versions of the...
thingiverse
Just the single screw I designed because I needed it for this project: https://www.thingiverse.com/thing:3516366
thingiverse
I use it for my logitech z906 You need: 5x M5 x 30 5x M5 butterfly nut 5x 1/4-20inch screw Note: Connector (Wallholder to Box) is easy to break if its PLA. ...I will design in the future a improved version of this.So be careful by tighten it or if u...
thingiverse
This bracket can be used for mini cameras and other devices with 1/4" threads. It is designed to mount a small camera by screwing it to a wall or a pillar for fixed-point observation. Requires M6x25mm bolts and nuts. The long bolt in the photo...
thingiverse
Original by yachtsambra https://www.thingiverse.com/thing:2310563/apps The screw in the model is floating which causes it to print in thin air and break. This fixed version moves the screw to correct the mistake. ...
thingiverse
No screws required. ...Can print without support. It supports the 1/4 inch screw mount for some logitech webcams (and others too I think) and does not require removing any screws/bolts to attach to the printer.
thingiverse
An adapter that converts a 1/2 inch female screw to a 1/4 inch male screw. A camera etc. can be attached to the tip of the stick of the tamo net that can be extended. After making 1_2To1_4ScrewA.stl, insert the screws and cover with...
thingiverse
Instructions I am switching to 1/4" lead screws on my new Prusa i2, since they are more flexible (less able to make the frame wobble when out of alignment), and they give slightly higher Z precision (20 threads per inch instead of 18). Just press...
thingiverse
**Required Components** * 1x **M3x16 Screw** - This screw is used as a core for the 1/4'' printed screw. A longer screw is okay for use as well, depending on your application. * **M3 Thread Cutting Tool** - Without the core M3 screw, the 1/4''...
prusaprinters
A different version of my screw I designed for this project: Lens Cap HolderThis is designed so that it can be printed lying on the print bed. ...I haven't tried it yet, but I hope it should be a bit stronger due to the direction of the force...
thingiverse
A different version of my screw (https://www.thingiverse.com/thing:3543376) I designed for this project: https://www.thingiverse.com/thing:3516366 This is designed so that it can be printed lying on the print bed. I haven't tried it yet, but I hope...
thingiverse
Customized version of https://www.thingiverse.com/thing:193647 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=193647
thingiverse
It's for invert use of https://www.thingiverse.com/thing:995503
thingiverse
Version with screw reinforcement. ... Screw: M2.5 35mm flathead
thingiverse
I was asked to modify my original file to have a 1/4 inch mount on it. (I have not printed this version, as I'm not certain as to how good the thread will hold under normal use) However, I have tested the 1/4inch thread with the insta360 selfie...
thingiverse
Customized version of https://www.thingiverse.com/thing:193647 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=193647
thingiverse
- Introduction: https://astronomytechnologytoday.com/2022/06/23/astrohopper - Program: https://artyom-beilis.github.io/astrohopper.html - Also see this adapter: https://www.thingiverse.com/thing:6052282 This uses: - a 1/4 inch phone screw (long) - a...
prusaprinters
But i needed a quick release base on my small desk tripod for usage of a dslr as webcam. With the print i can attache the existing camera mount (ground is round about 4.4cm x 4.4cm) plate on the quick release which is screwed on the 1/4 inch photo...
thingiverse
A single screw for this sony camera holster project: https://www.thingiverse.com/thing:2415868 that i remixed for a friend. ... Same height but a bit flatter than the original.
thingiverse
Adapter from 1/4 inch screws to 3/8 inch screws commonly used in photography, especially in tripod heads.
prusaprinters
just a ¼ inch screw with nutz, no special instructions here. see photos for reference.</p><p><strong>Print instructions</strong></p><ul><li>0.15mm layer height</li><li>10% grid infill</li><li>3 perimeters</li><li>I used PLA and it looks like it does...