10mm bearing 3d models
117192 3d models found related to 10mm bearing.thingiverse
adapter for this cable chain: http://www.thingiverse.com/thing:435597 to use a 10mm ball bearing and 3M screw.
cults3d
This sleeve, is designed to replace an LM10UU with a 27mm length of PTFE 10mm (10mm ID X 12mm OD) tube in it's center.
thingiverse
This sleeve, is designed to replace an LM10UU with a 27mm length of PTFE 10mm (10mm ID X 12mm OD) tube in it's center. Instructions Insert PTFE sleeve into smaller printed part, and cut to length.
thingiverse
... ...Bearing type (ZZ6000) : https://www.amazon.com/uxcell-ZZ6000-26mmx10mmx8mm-Shielded-Bearing/dp/B01JVND06C/ref=sr_1_1?s=industrial&ie=UTF8&qid=1487558182&sr=1-1&keywords=zz6000 The model housing diameter is 25.98, so the bearing would press fit.
thingiverse
Customized version of http://www.thingiverse.com/thing:138222 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=138222 Instructions Using the following options:...
thingiverse
Mancal e Base Mesa 10mm - Bearing and Table Base
thingiverse
Mancal e Base Mesa 10mm - Bearing and Table Base
thingiverse
Mancal e Base Mesa 10mm - Bearing and Table Base
thingiverse
I found the bearing hole too small to use a 623 bearing which is used elsewhere in the same project, this way i could take advantage of bearings i already have in hand. Prints with no support. ...25% grid infill, 2 perimeters, 0.2 layers printed in...
thingiverse
This is a replacement cover for a cheap Titan clone that comes with a non hollow gear shaft and larger than standard 10mm bearing. The original bearing holder breaks easily (when overtensioning) due to the thin plastic support. I used Ben...
prusaprinters
This is a replacement cover for a cheap Titan clone that comes with a non hollow gear shaft and larger than standard 10mm bearing. The original bearing holder breaks easily (when overtensioning) due to the thin plastic support. I used Ben Neubauer's...
thingiverse
This is my further modification of the indirect laser filament monitor to accommodate 10mm diameter bearings (623zz), which are easily available. I have also made the bottom section spring loaded so that the tension on the bearing can be adjusted. I ...
thingiverse
Just a mockup of a ceramic bearing (nothing rotates), with the following dimensions : - internal diameter 10mm - external diameter 26mm - thickness 8 mm
thingiverse
This is a custom part, the exact same as SC8UU but for the 10mm Rods.
youmagine
This is intended to replace an LM10UU bearing. While this has a bit more friction, the end result is pretty good. ...Although, I am looking for a different material to use that will make the friction coefficient a bit lower.
thingiverse
The original bearings on my TAZ 5 wore out and had 1mm slop after 500 prints, so I designed my own custom bearings. I used PLA to print these and so far they have performed very well. If these wear out too quickly I will try with ABS then Nylon.
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=120441 Instructions Using the following options: split_bearing = No height = 12 sidewall_thickness = 2 outer_diameter = 16 inner_diameter = 10.5
thingiverse
Customized version of http://www.thingiverse.com/thing:774334 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=774334 Instructions Using the following options: Spool_Diameter = 53.5 Bearing_Diameter = 10.0
thingiverse
Customized version of http://www.thingiverse.com/thing:774334 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=774334 Instructions Using the following options: Bearing_Diameter = 10.0 Spool_Diameter = 59.5
thingiverse
Customized version of http://www.thingiverse.com/thing:53451 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=53451 Instructions Using the following options: tol =...
thingiverse
Upgraded my bear mod to use 10MM Z rods, Still a work in progress. Also included a lead screw support if you need to use couplings. You'll need 2x flanged 688zz bearings for the Z toppers and the rod support i used 608zz bearings. ... Better...
grabcad
BF12-C7 Support Unit Free End for 10mm 6000ZZ Bearing
thingiverse
With support for up to 3 different bearing sizes Bearing number – inner diameter x outer diameter x thickness 608 - 8x22x7mm 696 – 6X15X5mm 606 – 6x17x6mm The parts are 15mm wide and comes in a big variety of tooth's. ... Feel free to contact me if...
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=107103 Instructions Using the following options: bearing_hole_diameter = 10 wedge_difference = 1.5 bearing_width = 10 bearing_outer_diameter = 10 spool_diameter = 52.3