2040 aluminum extrusion 3d models
54944 3d models found related to 2040 aluminum extrusion.thingiverse
Insert for Motedis 2040 Aluminum Extrusion. Allows the usage of M10 furniture adjustment screws as stand. ...Designed for BLV_mgn_cube.
cults3d
Insert for Motedis 2040 Aluminum Extrusion. Allows the usage of M10 furniture adjustment screws as stand. ...Designed for BLV_mgn_cube.
thingiverse
All you need to do is bolt these to the corner of your 2040 extrusion use two (or more) t nuts to bolt down the plate and use a 13/64 Drill bit to drill through each hole. They are designed to be a little smaller so the drill bit cant self...
thingiverse
I ran the cables through the extrusion profiles and then zip tied them in place. All the cables from the extruder ru through a single mesh fabric wrap that is held in place with zipties. I used a 1.5 inch mesh which is way too big. I will be...
thingiverse
Currently redesigning my Anet A8 Plus and wanted a way to cleanly fasten some cable tiedowns to the frame. ...I made two sizes to accommodate 2020 and 2040 extrusions.
thingiverse
Tool to assist you in aligning a tap to the end of a 2040 extrusion. This one is specitically designed for Misumi HFSB5 series, but should work equally well with any of the common extruded T-Slots as well as OpenBeam. Should work equally well with...
prusaprinters
This is a remix clamp-style mount designed to attach to the Prusa MK3s bear upgrade or any 2040 extrusion frame. It tightens with a screw and can be positioned anywhere. It provides two mounting holes on the top, two on the bottom, and four on the...
thingiverse
A simple remix for this squash ball feet to be used on the 20mm side of 2020 or 2040 aluminum extrusion / profiles. ...The holes are for M5, but they can easily adjusted by changing the measurements in the attached FreeCad file.
thingiverse
Isolation foot for corner of the Prusa Bear Upgrade (2040 aluminum extrusion) for use with sorbothane isolation pads. Isolate It: Sorbothane Vibration Isolation Circular Pad (.25" Thick, 2.25" Diameter) ...
prusaprinters
A simple remix for this squash ball feet to be used on the 20mm side of 2020 or 2040 aluminum extrusion / profiles. The holes are for M5, but they can easily adjusted by changing the measurements in the attached FreeCad file.</p> <h3>Print...
thingiverse
this is not a part to be 3d printed, but something that you can use when building your 3d assemblies.
thingiverse
you also need: 2 ball bearings for the idler, 1 M4 screw (i used 60mm) 1 M3 screw for the idler 2x M4 Insert nuts for wheel and idler (because hex nuts are inferior) various washers, nuts etc for fixing it to the extrusion. The Stepper holders are...
prusaprinters
Belt tensioner for Y Axis. you also need: 2 ball bearings for the idler, 1 M4 screw (i used 60mm) 1 M3 screw for the idler 2x M4 Insert nuts for wheel and idler (because hex nuts are inferior) various washers, nuts etc for fixing it to the extrusion....
prusaprinters
Belt tensioner for Y Axis. you also need: 2 ball bearings for the idler, 1 M4 screw (i used 60mm) 1 M3 screw for the idler 2x M4 Insert nuts for wheel and idler (because hex nuts are inferior) various washers, nuts etc for fixing it to the extrusion....
thingiverse
This is a heavier duty remix of the original design, adapted to fit a 2040 aluminum extrusion as used by this (https://www.thingiverse.com/thing:2263216) upgrade for the Anet A8. The original design was great so I thought I would use it as...
thingiverse
M3x30 screws and M3 nuts for securing parts to eachother. M5x8 and tnut for securing to profile. ...Added backing for countersunk fastening screws.
thingiverse
Simple and quick spool holder for 2020 or 2040 extrusions. Requires an 8mm rod, two m5 screws, two m5 hammer/t-nuts, two m3 screws, and two m3 nuts. The bracket holds the rod at a slight angle so that the spool can't fall off of the end. Make sure...
thingiverse
I really liked this enclosure design, but i wanted to mount it to 2020 extrusions so i added some mounting holes. I didn't like the big ventilation slots on the top cover, so i added ventilation slots in the bottom shell and added several different...
thingiverse
This is designed for a bowden connector with M10 threads. ...Mirror the part if you want to install it on the right hand side of your printer instead of the left.
thingiverse
aluminum-extrusion-2040-european-specifications