20mm chain 3d models

Customized version of https://www.thingiverse.com/thing:881114 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=881114

Customized version of https://www.thingiverse.com/thing:881114 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=881114

... was planning to use on one of my printers. The chain itself came from aliexpress and has no manufacturer but it looks similar to the bulk of chains available on amazon and ebay. They hopefully may come in handy for somebody. ... Enjoy :-)

In rebuilding my Prusa i3, I wanted a more attractive way to attach my 20mm Cable Chain - http://www.thingiverse.com/thing:10946 (in particular items End1 and End2). I bastardized the following X endstop - http://www.thingiverse.com/thing:158434 to...

... It's also compiled with trace_width = 0.66 and layer_height = 0.3 (2.2 WOT). If you want to compile it yourself, you'll also need one of the files from the 20mm chain (http://www.thingiverse.com/thing:10946) in the same folder as this scad.

After printing out the zip-tie cable chains included in the Voron STL's, I went looking for some different chain. I liked diogosantos88's chain for the Ender 3, it is a design with open channels and locking clips so you can drop the wire right in...

This remixes an existing 20mm design to accommodate a different type of screw (M3 socket head cap screw bolts) and to include a middle link that can be screwed down. ...It's compatible with the original so you can mix and match.

A drag chain mount to replace the original drag chain with a 10mm x 20mm drag chain as the original sags. You must purchase a 10 x 20mm drag chain of length 1 meter. check mounting before purchase as it may differ from the one this is designed for....

A drag chain mount to replace the original drag chain with a 10mm x 20mm drag chain as the original sags. You must purchase a 10 x 20mm drag chain of length 1 meter. check mounting before purchase as it may differ from the one this is designed for....

Some of the parts I used in my C/D-bot build if anyone else finds them useful. ... To be used with 20mm cable chain (http://www.thingiverse.com/thing:668048) .

Some of the parts I used in my C/D-bot build if anyone else finds them useful. ... To be used with 20mm cable chain (http://www.thingiverse.com/thing:668048) .

I made a couple of mild modifications to reduce the steep overhangs that were giving unreliable prints with this part. ...Nothing special, but it might make life a little easier for someone else.

I added two end parts and opened up the links to be able to get the cable in when the chain is in place. Put the links every other left and every other right. :) Update: Replaced the skp file with a new one also containing smaller version of the...

I added two end parts and opened up the links to be able to get the cable in when the chain is in place. Put the links every other left and every other right. :)</p> <p>Update: Replaced the skp file with a new one also containing smaller version of...

Cable chain remixed to fit onto Openbuilds V-slot or other 20mm extruded aluminum railing types. Scaled down the width of the chain to 20mm to match the rails, modified the end pieces to accept a single bolt. ...Attach at each end with an M5x8mm...

Cable chain remixed to fit onto Openbuilds V-slot or other 20mm extruded aluminum railing types. Scaled down the width of the chain to 20mm to match the rails, modified the end pieces to accept a single bolt. ... Attach at each end with an M5x8mm...

Calibration Cube 20mm XYZ Key Chain Test your XYZ for step mm calibration Test your circle shape (basically test about your belt system) Test your overhang All in one test and you get a key chain Test your printer without wasted Filament

Customized version of http://www.thingiverse.com/thing:1078216 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1078216 Instructions Using the following options:...

Customized version of http://www.thingiverse.com/thing:1078216 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1078216 Instructions Using the following options:...

I wasn't happy with the inside diameter of the other cable chains, so I edited an existing design and created this one :) You can check out the video here: https://www.youtube.com/watch?v=GGb_3tLH8zI If you haven't already, make sure you subscribe to...

Walls are approx 2mm thick (give or take for tolerances) Lots of access to cable to rearrange or help feed cables through the chain Small guide around the circular insert to cut a groove into the mating plastic chain link. Makes movement a bit...

I modified the standard calibration cube to allow for more flaunting. ...I present to you, the best way to show off your 3D printers capabilitys to everyone around you.

A new design easy-print inner open cable chain, now that I've learned CAD. See also my somewhat more hackneyed design with larger links: https://www.thingiverse.com/thing:4885141 Recommend printing these in PETG. I used to use ABS for links but it...

*** A new design easy-print inner open cable chain, now that I've learned CAD. See also my somewhat more hackneyed design with larger links: https://www.thingiverse.com/thing:4885141 Recommend printing these in PETG. I used to use ABS for...

These should work better for less precise printers. A new design easy-print inner open cable chain, now that I've learned CAD. See also my somewhat more hackneyed design with larger links: https://www.thingiverse.com/thing:4885141 Recommend printing...

made this drag chain for my workbee cnc , is studeid for the X axis , made to self align on the 20mm estrusion vslot on the backside , so can be used on any vslot extrusion for general purposes. ... parts are divided: START : for the starting piece IN :...

made this drag chain for my workbee cnc , is studeid for the X axis , made to self align on the 20mm estrusion vslot on the backside , so can be used on any vslot extrusion for general purposes. ... parts are divided: START : for the starting piece IN :...

Same as the original remix but the enclosing bar is arched upwards. Allows my pre-made cable end to fit through while still clearing the tightest bend. Also prints better without supports. No other changes. ... (second try)

- There are ends to every width - Since you have to change a cable at some point (often there are no cables installed, which have corresponding motion cycles), I have designed the chain as a flap. A piece of filament serves as a hinge. Simply slide...

Larger sized drag chain for CNC plasma cut tables, CNC routers, CNC mills, power, data, coaxial, and other cables/cords.&nbsp;This is a two-piece, snap-open drag chain, with an inside track dimension of 20mm x 40mm, and it's designed for a 64mm...