3 Axis Gimbal for GoPro2 with Storm32 BGC 3d models

I recently upgraded my CNC laser to a three-axis control panel and discovered that it didn't come with a necessary mounting plate.

with this support, replacing the original, the Z axis motor can be moved sideways in order to make the bar as straight as possible

So I wanted to put on a larger motor and a dampener for the y and x-axis on my Ender 3. Turns out the motor was far too big and when I went to make a whole new bracket I had an idea: just flip the Y-axis bracket vertically and mount that way. The new...

Z axis cable loopsPrintined at 0.125 for smoothness, but supports can ruin that. ...Easy print.</p>

I like this solution because it lets the Z axis move with the print and the camera isn't in the way of the heated bed. Just screw the webcam to the arm using a M3 x 16mm screw and just use your X Endstop cover screws to secure the arm to the...

It might be neccesery to grind the big hole in the middle with sandpaper to fit the z-nut properly.For detailed information referhttps://github.com/Creality3DPrinting/Ender-3If you can see, i changed the steppers earlier for better performance.But...

``` v4l2-ctl -d /dev/video0 --set-ctrl=focus_auto=0 v4l2-ctl -d /dev/video0 --set-ctrl=focus_absolute=30 v4l2-ctl -d /dev/video0 --set-ctrl=power_line_frequency=1 v4l2-ctl -d /dev/video0 --set-ctrl=sharpness=200 v4l2-ctl -d /dev/video0...

Webcam holder for Ender 3, which is fixed to the X-axis stepper motor cover.In the plastic cover there is a small cutout on the bottom, where you mount this holder using the included clip.You will need one M3x12 (or longer) screw and nut.The nut is...

... extruder en did not had the hardware lying around. ... This is a cable chain for the Z axis and no hardware required Also remixed the chain link from diogosantos88 so it would hinges backwards (see foto) 22 cables chains are needed for the Z axis.

Edit it online https://tinkercad.com/things/3cdQ294cnmj Modified version of stabilizer made by Adoniram Instructions I started with Adoniram's Y axis stabilizer I used his bearing holders then made up a different mount with a tension spring I got at...

Rocksolid part now. Need longer screws and an ajustable motor mount like: https://www.thingiverse.com/thing:3603432 Z1 Plate is the mirrored version of Z2 with clearance for X Motor, it also removes Extruder motor, this is only for Direct Drive or...

The rods are 7-inch long 3/16 music wire with a 90-degree bend at 1 inch from the end, and the bearings are 5x11x4 mm as per Adoniram's instructions. To fit the ends of the wire into the bearing holders, I ground them slightly. After centering the...

This upgrade enhances the stiffness of your Y-axis-carriage on your Ender 3. It's built on a standard Ender-3 and should work well on an Ender-3 Pro too. I created this upgrade because I wasn't satisfied with the wobbly bed of my Ender from day one....

https://www.amazon.com/Sydien-Pillow-Flange-Bearing-Self-Alignment/dp/B07C4Y7P2C/ref=sr_1_3?crid=1KPNI9SDV00YL&dchild=1&keywords=pillow+block+flange+bearing&qid=1602605305&sprefix=pillow+block+flan%2Caps%2C313&sr=8-3 a. Bearing for bottom leadscrew...

Often times I have experienced that the Y axis of a 3D printer gets bent or broken. ...This part acts as a replacement. You can take the 3D print of this and install it in your 3D printer.This part is of Ender 3 3D printer.

A specially designed 9mm Spacer enables the installation of an E3D stepper motor on the Y axis of an Ender 3 or CR-10, ensuring that it clears the back end stop switch without interference. ... Long M3x50mm countersunk bolts must be used in place of...

The crank now threads down smoothly onto the rod, winding the Z-axis up with ease. ...It won't lower the Z-axis back down, instead backing off of the rod, but that's not a big deal since 99% of the time I need to adjust the Z-Axis is to lift it out of...

Knob for Ender 3 Pro \r\n\r\n Size 13 x 3

An Ar Drone 2.0 features a two-axis gimbal, compatible with cameras and a 9G hobby servo. ...Although I have not personally tested this, it may prove beneficial for others to try.

Adjusted the case so it didn't hit the bracket for the z axis guides, and made the clearance in the side wider for the larger screw head. ... The threaded portion has had the inner channel narrowed to fit the enders smaller pulley and the hole size...

The holder for Z-axis motor. It has the ability to adjust the position in two planes. Screw slots have a small stroke, which allows you to more accurately align the screw of the Z-axis. 4 mounting points for the motor and holder give a more rigid...

After testing several Z Axis mods downloaded from Thingiverse, I thought I'd design my own, with the objective of:be as thin as possiblebe lightweightbe rigid enough to withstand the speed of travel.use the existing support on which the laser head is...

The product is almost a scam, it's bad designed and it covers part of the Y Axis preventing the motor to step correctly and causing the whole Axis to grind, damaging the printer. To fix this you need to print 2 cr4p fixers and screw them (with...

... flat sides down of course. (Motor side with the motor recess up, so there's less support needed under the smaller recess for the extrusion. ...The other side needs no support, just lay it flat with the posts sticking up) Category: 3D Printer Parts

After testing several Z Axis mods downloaded from Thingiverse, I thought I'd design my own, with the objective of: * be as thin as possible * be lightweight * be rigid enough to withstand the speed of travel. * use the existing support on which the...

I updated mounting those Y axis bar mounts to the CNC table with wood screw from above. I used 4,0x30 mm wood screws to attach to the CNC table. ...I used M3x16 machine screws to attach to the bar mounts.

this will not need any support can be used if u are gonna switch the y axis stepper with the extruder stepper to reduce weight u might want to print it in a durable material so it doesn't wear as the original one was hardend steel

I updated mounting those Y axis bar mounts to the CNC table with wood screw from above. I used 4,0x30 mm wood screws to attach to the CNC table. ...I used M3x16 machine screws to attach to the bar mounts.Printing instructions:filament PET-Gprint in the...

I knew crafting those Y axis bar mounts would be a challenge, especially when it came to assembly, disassembly, and reassembly. So, I designed these small plates that can be attached to the CNC table from above. These plates are secured using M3x15...

I knew mounting those Y axis bar mounts would be a problem, not to mention assembly/disassembly/reassembly, so I did up these little plates so they can be attached to the CNC 'table' from above. Uses M3x15 machine screws to attach to the bar mounts....