aquarium heater protector 3d models
23264 3d models found related to aquarium heater protector.thingiverse
More Information: https://www.reef2reef.com/threads/diy-4ch-heater-controller-arduino-based.629476/ https://github.com/spaelectronics/4CH-Aquarium-Heater-Controller If you like what I've done, please consider sending a donation:...
thingiverse
This is a replacement mounting bracket for a Fluval aquarium heater. It has two spots to mount suction cups that came with the original bracket. The original bracket had loosened over time and my heater was slipping down into the water. This design...
thingiverse
I designed this bracket to hold two aquarium heaters, which live in the bottom of the sump under my 125 gallon aquarium. The suction cup holders that came with the heaters had become brittle, and they don't stick very well to the bottom of the sump...
thingiverse
Meant for a Hygger HG-802 titanium aquarium heater and marina LED 20 gallon aquarium but will fit any heating tube 0.75" in diameter. ... I also coated it in low viscosity epoxy (thin coat) to ensure the PLA doesn't leach.
thingiverse
A replacement clip for a glass submersible aquarium heater. I use one on the top of my heater tube (the cool end), even though I'm using PLA it should be fine with the temps. ... I dont use any oil on my filament so I figured this would be safe in my...
thingiverse
I didn't want our turtle to break the glass aquarium heater so I designed this guard to protect it. Slightly based on some pictures from stores selling these. It's designed for my "Aquael comfort zone gold 200w" heater but might fit others as well.
thingiverse
Aquarium Heater holder. Designed for 90mm wide heater throat with clearance . Has a Adjustment screw to adjust the heater cord out of the top of the water. This bracket is meant for a TANK With plastic trim.. The Screw Might and Nut assembly is...
prusaprinters
I didn't want our turtle to break the glass aquarium heater so I designed this guard to protect it. Slightly based on some pictures from stores selling these. It's designed for my "Aquael comfort zone gold 200w" heater but might fit others as well.
cults3d
... reinforcements (2 holes of 4.2mm and screws of 5mm). The heating hole is conical, 23mm at the bottom and 29mm at the top. The water line is between 27mm and 35mm from the underside of the aquarium reinforcement. ... Made of Food PET-G filament
thingiverse
A guard for an internal heater. Have an anemone that wanders or other livestock that can get burned? Add a guard! Print as is, no supports with 100% infill. The pegs are used for suction cups. Glue the peg into the suction cup then use a...
myminifactory
A guard for an internal heater. Have an anemone that wanders or other livestock that can get burned? Add a guard! Requires 4 standard suction cups that have a insert hole. (got mine from a spray bar that came with a cannister filter) Print as is,...
thingiverse
This is a support for a water heater for aquariums the heater diameter is 23mm the glass is 6.5mm thik Hope it helps. ... Regards !!
thingiverse
Support de chauffage d'aquarium pour chauffage diamètre 22mm, et vitre de 8mm. ... - Aquarium heater support for 22mm diameter heater, and 8mm glass.
cults3d
Support de chauffage d'aquarium pour chauffage diamètre 22mm, et vitre de 8mm. ...Nouvelle version sur Thingiverse. https://www.thingiverse.com/thing:4104945 - Aquarium heater support for 22mm diameter heater, and 8mm glass.
thingiverse
This is a protective cage for use with a "hygger 802 Aquarium Titanium Heater Tube Heating Element / Heater Rod (500W)." To install, remove the flexible cap from the end of the heater rod and push it into the larger of the two holes in the printed...
thingiverse
Hi, I made this part becaus the crappy suction cups of my Eheim heater always losen up. Fits to 75W and 135W. May also fit to other sizes. Fits on 5mm glass. ... Print with 100% infill or it may float.
thingiverse
I was tired of the suction cups that often detached from the glass and I decided to make a holder that can be hung on the glass of the aquarium. Model made in Fusion 360 If you found this useful, please donate what you think it is worth to my...
cults3d
Artillery X1 TPU Heater Block Protector Cover, Artillery Artillery Heater Block Protector Cover
thingiverse
With some MK3 builds, the flexible, fabric covered heater bed cable rubs against the rear printer frame as the bed moves during printing, damaging the fabric cover and potentially the wires therein. ... This part slips onto the connector on the rear of...
thingiverse
Aquael Hexa set II 60L Aquarium heater stub. ...If the heater is not required you can use this stub.
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/euTeIJGdk4H
prusaprinters
<p>This thing was made with Tinkercad. ...Edit it online <a href="https://www.tinkercad.com/things/euTeIJGdk4H">https://www.tinkercad.com/things/euTeIJGdk4H</a></p> <h3>Print Settings</h3> <p><strong>Printer Brand:</strong></p> <p>Monoprice</p> <p...
thingiverse
This is a clamp for a Hydor ETH 300 in-Line External Aquarium Heater so you can attach it to the inside of your cabinet. You will require 2 x countersunk screws to fasten it to the cabinet and 4 x M3 screws and 4 x M3 nuts to join the two pieces...
thingiverse
**Note** A broken aquarium heater or pieces of plastic in the water tank is going to damage the pump and probably other components of your chiller and/or laser if a broken piece makes it into the circulating water. ...By using this item you assume full...
thingiverse
DualAquariumHeaterHolder_BRS_Schego_LessMaterial_And_Endstop.stl - Removed some side material on the base, took away the rounded corners, extended the end of the base to allow a 1/4" end stop the heaters can rest against to prevent the heaters from...
thingiverse
Customized version of http://www.thingiverse.com/thing:337535 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=337535 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:337535 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=337535 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:337535 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=337535 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:337535 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=337535 Instructions Using the following options:...