3 5 sata hdd 3d models
1057736 3d models found related to 3 5 sata hdd.thingiverse
This enclosure holds a *3.5" SATA Hard Drive* (via side mounted screws) for use with a *SATA to USB Adapter* (There is a cutaway in its front to accommodate such an adapter). ... I use this combination as an external clone of my System Drive.
thingiverse
I modified the top and bottom to have ventilation, also I change the top to be more slim (the walls), use less plastic and 5 hours less of printing. In my case I printed using PTEG filament. ...
grabcad
This is a generic 3.5 inch sata drive. The primary reason was to make a hdd case where the outer dimensions and mounting options need to be correct. - Unbelievable, this does not exist in 2021 yet for solidworks...The model is relatively low detailed...
thingiverse
3.5" SATA disks enclosure for 4 disks. Print it front side down, without any support. ... FreeCAD model included.
thingiverse
Hi, I was trying to achieve a relatively low cost NAS with open source capabilities so I decided to move my 2 3,5" HDD from external USB cage to single box together with Rasbperry Pi 4 B 8GB RAM model. This has been achieved with 2 pieces of...
thingiverse
... are the screws that I used with them but any similar should work fine. https://www.ebay.com/itm/Supermicro-Screw-Bag-and-Label-for-24x-Hot-swap-3-5-Inch-HDD-Tray-Cable-100-pcs/252937200149?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2060353.m2749.l2649
thingiverse
... need. 2.1.1 HDD Caddies - Yet to make Doors SATA BackPlane Rear Cooling Ducting Print Settings Printer Brand: RepRap Printer: MendelMax 2 (home brew) Rafts: No Supports: Yes Notes: HDD Tray The openscad already comes with supports for the overhangs.
thingiverse
Customized version of https://www.thingiverse.com/thing:1595628 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1595628
thingiverse
A protective enclosure for 3.5 Inch desktop size SATA hard drives (HDD).** The rear cutout allows easy access for USB-SATA adapters. Use the vertical drive rack to organize a collection. ... ** This is a resized version of the 2.5 inch HDD Case
thingiverse
This enclosure can hold a either a SATA or IDE 3.5" hard drive or a 2.5" "with an adapter" hard drive fastened by side mounted screws. The enclosure can be used with or without the lid. There is a cutout in the back to accommodate various...
thingiverse
My SATA adapter didn't fit so I made this remix. ... Printed in PET-G on bare glass, no adhesive, 0.28, 235/75, 20 lines brim Very good design for the original thanks for sharing :) v1_orig_secured is the original lid plus two screw holes for...
thingiverse
This is a Vesa adapter for a Vantec 3.5" hard drive case. I used this mount a hard drive to a television to make a media player. There are many fine Raspberry Pi vesa cases you can bolt on top of it. ...
thingiverse
This adapter allows 2,5'' SATA drives, for example most ssd's to be used more easily in hot swap bay. Requires 2x M3x10 countersunk screws to work NOTE! ...If you are looking for more permanent mount for your ssd inside your case, this one is not...
thingiverse
I just did a quick tinkercad bad remix on the original to get it to fit correctly on my setup. ...I figured I may not be alone here so uploading for others
thingiverse
It places SATA connector of 2.5" hdd the same place 3.5" hdd has, so it can help you fit 2.5" HDD in places where only 3.5" hdd fits and SATA connector is soldered to fit 3.5" hdd. ... You need 2xM3 washers, 2xM3 screws and *detachable thread locker*...
thingiverse
Since I needed a case for a 2.5" hard disk that was still lying around here that would work with this:...
thingiverse
This is an enclosure for a 3.5 sata HDD and a USB 3.0 adapter. The picture shows that I misplaced the side mounting hole at the rear of drive, but the scad and stl files have been corrected since the print. Just attach the HDD and adapter to the...
thingiverse
2.5" SATA HDD case Updated your laptop with SSD? Don't throw the HDD, make an external storage from it. Requires a SATA-to-USB cable (~2$ in online shop), 6 of 6mm length 3mm diameter bolts and 4 nuts. ... In general, no glue is needed, but might be...
grabcad
Laptop Hard Drive HDD SATA 2.5 inches.This hard drive is inspired by the Seagate ST3000LM016, with real mounting dimensions.
thingiverse
Secures a 2.5" SATA hard drive or SSD in a modded "phat" PS2. Print with very little infill as its meant to bend a bit to fit snugly inside the console. Just secure the drive to the mount, plug the drive into the HDD/Network adapter and carefully...
grabcad
... Remember to credit me when you are doing so.All dimensions are 100% accurate.-Ask for the STEP file if you need it. (please ask me in private message)Other harddrive 3D models:Intel 2.5" SSD 520 SeriesSeagate 7mm 2.5 HDDHITACHI 3.5" Harddrive SAS
thingiverse
12 bays cabinet for 2.5" drives. ...https://www.tinkercad.com/things/3F9p1GGuQx0-12-x-25-hdd-cabinet
pinshape
Summary SATA Connector protective cover for my HDDs when not being used.