3d bus model

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_pattern_element_shape = 3 custom_right_port_length = 30 stencil_drawing =...

Safety Information Please be aware that this product contains small items and is not suitable for young children.This product is a scale model and is intended for use by adults and children age 14+.Take care during use as some products may...

Not a problem with a well-tuned MK3S+.    The box was printed usingFilament                                              ...

-Number of facets causes extreme delay in saving/rendering model, likely due to me not understanding the correct scad approach; I am still learning, feel free to leave me any feedback so I can improve my techniques. -Flat ring design (just like the...

In addition, in case you want to remix you would potentially only have to adapt the holder model.The bottom of the holder has a cavity that exactly fits a specific lightning cable found on Amazon with angled connectors to reduce the space it...

The model was inspired by [this map pocket on Amazon](http://a.co/5P0dMfJ), but larger and with more holes for the bungee cords. ...I have no affiliation with this product and my design was done by hand, so please don't sue me if that's your map pocket...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_x_position = 20 custom_back_camera_corner_resolution = 8 custom_bottom_fillet_resolution = 8 stencil_horizontal_position = 50...

Some of the models are difficult to hand-launched and should be tested with a 1/16" rubber band instead. A slight elevator-up reflex is required for flight. This is accomplished by latching the elevons up on the relex tabs on the aft end of the...

Printer Settings: * Printer Brand: RepRap * Printer Model: Original Prusa i3 * Rafts: No * Supports: No * Resolution: 0.2mm * Infill Percentage: 25% Print Notes: I utilized a 0.8mm nozzle to expedite the printing process, which took approximately...

This model currently comes in 4 variations. Standard rail facing forward. Standard rail angled 5 degrees to the side off the rail. Standard rail with sidekicks facing forward. Standard rail with sidekicks angled 5 degrees to the side off the...

Note: A Honeywell Type H filter is virtually the same size (though not tested with this model) and 3M offers a filter that claims to be compatible with both the Aer1 and Honeywell Type H. 36x rare-earth magnets, disk shape, 8 mm diameter, 3mm heigh...

**Just make sure they are all the same voltage and be very carefully** - **3S BMS 20A** - I used the HX-3S-FL20 REV2.2 Probably they are more models similar to this, this was the name I found. This is for controlling the charge and discharge of the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 4 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 printer_tolerance = 0.25 stencil_pattern_line_thickness =...

For that reason, the drawers shown here have been modeled by means of [OpenJSCAD](https://openjscad.xyz/dokuwiki/doku.php), which give you the possibility to adjust them just by changing a few numbers and [rerun the script in your...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

the vanilla singleplate model), though the pulleys included here are a bit different from those. Re-cut bolt/nut holes in the idler pulley holder and thumb wheel to accept M5 hex bolts (because those are all I have with hex heads :-P ) Added an M5...

The handle houses the controller with its user interface and no base unit is required.All that is missing to be the perfect soldering solution for workbench and mobile needs is a stand and a housing.Introducing TStationThe TStation is a case for the...

... - Schematics:  Goggly eyes are optional, but they improve performance and friendliness of the finished project. Modelled using tinkercad & blender. ...

This model is cheaper than the usb c version and charges the Oculus Quest perfectly. This greatly improves your playing time and you could even charge the battery while using it. One design came close to what I liked, but was made for a different...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_pattern_element_shape = 3 custom_right_port_length = 30 stencil_drawing =...

The models (keys and legends) are the same dimensions and should center at the exact same spot. It’s really difficult, and you will fail again and again, but the result is worth it (I think). You could also print the keys upright (with supports) and...

(The toothbrush still shouldn't fall out, but a hole any larger and it might...)(I also use a print of the original model as a holder for fine detail paintbrushes, so a hole in the bottom of that one would be rather pointless.)Enjoy!Print...

[Medium Sized Model - 25mm Base] [Presupported in 32mm & 75mm scale]   A Ranger from Nan Thalias. Ervion was sent as part of an Elven diplomat’s escort, alongside his father which was attacked by a retinue of goblins and bandits near the County...

Many thanks to Dalek_Kolt for providing the original model, you can find more ripped stuff from them here: https://www.vg-resource.com/thread-39778.htmlDisclaimer:The figure you see in the photos is a larger version that houses LEDs and batteries. If...

One uses a buck converter that is very difficult to find at the moment, so this model is not uploaded. This is the one I use. The other one has a larger area inside so you can fit other converters, should you want to. You can ignore the converter and...

This is a stepper motor-controlled model turntable designed for 009 but compatible with short N gauge locos (loose the fences). The bed is 100mm long, and the Arduino code will follow in the coming weeks. Primarily designed for DCC++ JMRI CMRI...

If you want to save time while testing, you can print the included calibration test instead of the full model, but that is optional.Once the egg halves are printed, screw the threads in and out repeatedly to remove any stray particles. It may feel...

Tensegrity model maintaining stability with one single wire.Materials needed:0.5 mm nylon wire7x M3 nuts7x M3x10 mm Allen screws (longer ones were cut to the right size)wooden plank of about 55 cm2x 50 mm wood nailsThe spiral parts are designed to be...

DescriptionThis is a fast and easy to print model to calibrate your new filament. It can be used to find the right settings for the extrusion factor to get the right wall thickness.</p><p>It is designed with a 0.86 mm wall thickness to meet the...

Will require manual tapping. Base Base_Type - The type of base (round or rectangular) Screw_Hole_Diameter - The diameter of the screw hole Screw_Head_Diameter - The diameter of the screw head Screw_Head_Countersink_Angle - Screw countersink angle...