3d model at at

Both are worth visiting.As for the model, I aimed for maximum accuracy, however, I burned out a bit in the end, and mainly the portal is a bit simplified.The STL file has a default 1/87 scale, however, in that size, some of the details on the portal...

I've made them so you can easily fit 4 of these into Normandy'44 (or any 1 inch box for that matter) giving you a total of 60 trays to work with.The model has mounts for 3x2mm round magnets which then hold the lid. I recommend placing them in the...

Expect my next update to add the magnet holes to the other models and hopefully make a lid that goes with them. You can see @modernespiel's design here: https://www.thingiverse.com/thing:5792535 ...

The design uses the previous facility of supplying electrical connections to the enclosure lid via pogo pins modelled into the leg adaptors. This allows the cover to be removed easily without having to disconnect and reconnect electrical plugs. The...

If it fails in the future, which is unlikely, I can simply print a new one for a few cents. Since this could be useful for other bike models or types, I added the FreeCAD V0.19 source file which allows changing the measurements. Update: 30.Jul.2020...

While designing parts for a “Thomas” size model railroad I found that “Matchbox Cars” had the wrong scale. A “Matchbox Car” was almost the size of a “Thomas” engine, so I needed cars built to a smaller scale.  Also, they shouldn’t look like...

You will find a version on the Models from now on. Update: 2019-10-15 Version 0.8.3 is out with the rear end Update: 2019-10-18 Version 0.8.5 is out with some modifications for better printing (And Including a first one-piece Chassis for larger...

MATERIALS/PRINT INSTRUCTIONS: *All models are already oriented for printing* 1 x Endplate - Use supports, 3-5 walls/floors/ceilings, ~25% infill 1 x Baseplate - No supports, 3-5 walls/floors/ceilings, ~25% infill 1 x Lever - No supports, 8+...

... with 80mm and dual 80mm fans. 5/2/2020: Added a new bottom section that fits the Raspberry Pi 4B. 4/16/2020: Added a diagram of the control boards and their positions in the box. 4/14/2020: Updated the lid fan hole positions and reuploaded models

This volume is enclosed by angles and curves, making it a challenge to model something to fit in there. The screen itself is also angled, and I wanted to have my design follow the screen face to make a better visual impression. And on top of that, on...

They also cut along main aspects of the model that would result in much needed cleanup on reassembly. The original was also designed more as a prop than a mask to wear. Since it had no breathing holes, I added some that were in the spirit of the...

I did try fitting the Model B+ but it didn't fit. If the Pi Zero doesn't meet your needs, there are plenty of Pi 3 boxes available. *NOTES: A few users reported that they had to extend some wires because the GEN L board sits further forward, while...

Just click the “Support & Join”  button beside my name or here: https://www.printables.com/@GigaPenguin#join:279  Exclusive models are included too! You can also support me through Patreon too:...

16 skate bearings (608) 26 5/16 inch nuts 14 small washers This was modeled in Sketchup. The files were converted to STL format using the SketchUp STL plugin. The files were checked for manifold errors using the Solid Inspector plugin. And the...

Laser Carrier Offset * Y axis: 58.60 * X axis: 17.00 The hot end shroud model is included in the files. ... Gcode Start Gcode * G21 (set to metric) * G90 (change to absolute positioning) * G28 (home all axes) * G1 Z100 F3000 (move to start height) *...

________________________ Update 07.05.2021 -Reuploded models 2 and 11_full. Both had errors that prevents them from printing properly. ... ________________________ <b>If you like my work please consider supporting me on Patreon.</b> <a...

As opposed to the similar looking ft compressor, this model conforms to the ft 15mm standard with a length of 60mm, and offers different connector choices. The bottom part comes in two versions. The one with peg is difficult to print, as it is easy...

This design is compatible with both the original & OLED model Nintendo Switch. Print settings: Use tree supports (on build plate only) when printing the PC case & display monitor. The files that require supports are named:...

This kit is modular and includes:  10 separate riders 10 separate horses 3 separate shields 1 separate lance  All models are supplied as both Pre-Supported and Unsupported 28mm scale STLs and LYS files. 13th century mounted Teutonic Knights...

To untie pull the ends apart again but pull one end towards the larger part of cutout and it will release.&nbsp;FilesIf 10 different sizes aren't enough for you, I attached parametric model in .f3d (Fusion 360) file and by changing parameters...

I am also including the model of the cover with its holes covered by a 0.2mm thick polygon. This is done to avoid problems when printing the parts. On my printer the small holes on the initial layer are not printed well and often printing the parts...

... (UNLESS you downloaded already redesigned carriage). Print the provided template model that would give you a pretty good guide as to where to cut. ...If the motor bumps into the belt, move the pulley that's on the X motor back as far as it can go.

2021-04-07: Revised models of chassis and actuator wheel printed. 2021-04-08: The first half is now assembled and a quick test with directly connecting the motor to the battery looked pretty promising. Will start working on the code while printing...

I really liked the compact ATX benchtop PS by gdoniu93 and started out simply to recreate the model in Fusion360. Somewhere along the way (as it often happens with me), I decided to totally redraw the original design to better accommodate some minor...

The bearing's basic design remains the same as previous versions, with a structure similar to the V2 model where the cage bridges cleanly over the rollers entirely (I've removed the V2 design since it's now obsolete). I have added loosening slots to...

So far I modeled a battery tray to hold a shorty lipo battery and secure it with a rubberband, hair bands, or a velcro strap. The hooks on each end (3 on each side) can be cut to allow of battery tray positions to fit. I will work on adjusting them...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_resolution = 8 custom_right_port_corner_radius = 5 custom_back_camera_x_position = 0 custom_bottom_port_length = 40...

I bought one just to model for y'all, strangers on the internet.Modular quick release module bay for your DJI FPV Goggles. For the <i>V2 Adapter Board</i> (<a...

That's why I have build sanding blocks from wood and purchased a commercial model. Now I wanted more of them to have a block for all grits I usually use. However, I didn't want to spend another 20+€ for a commercial one from Milescraft nor spend the...

... blocks that attach to the supports. On a perfect fit, it should almost snap into place. Use superglue to ensure the wings don't come apart. However, I advise gluing the entire model together. ...Use your judgment based on the precision of the print.