3d model of atomic structure

...BE MINDFUL of the data direction. Peel and stick LED strips into the appropriate length aluminum channel. Stand-off covers can be slid/pressed on. For this project I assembled them in sections so having to manhandle the entire length was not needed.

Required Materials (US): (1x) https://www.filastruder.com/collections/titanextruder/products/e3d-titan-extruder (1x) https://www.filastruder.com/collections/electronics/products/compact-but-powerful-motor (1x Groovemount for 1.75mm)...

Now, depending on how well your printer is dialed in, I would suggest creating custom supports for the switch cutout and the USB cutout on the battery/ electronics box, if this is done with the thinnest possible brush and then trimmed down some, you...

Parts List Hardware: A mountainboard (obviously!) https://www.mbs.com/boards/10101-mbs-colt-90-mountainboard-constellation 10-tooth motor gears (2)...

Some of my other designs: https://www.thingiverse.com/thing:4165457 - Smoke Stack Addon for Sector Mechanicus https://www.thingiverse.com/thing:4120637 - Sector Mechanicus Wall Link https://www.thingiverse.com/thing:4231310 - Sector Mechanicus Wall...

The corners of the bed are currently in their fifth revision, and while there's still room for improvement, this is as good as it gets for now. The idea behind the design is to use two bearings and a collar in each corner to preload the bearing and...

I printed all parts out of carbonfill. Very light and Stiff. It works very well. ...All you need: 3x MGN12H 400mm...

Picture frame (3 versions) Stl-Files (without configuration)3mf-Files (with configuration) for MK3S and Mini Printfiles (G-Code) for MK3S and MiniSimply slide in the back plate, then push the plate back a little at the free end (the side...

The platform is fastened with the front and rear screws of the trusses. These have to be replaced by larger ones. But be careful not to tighten the screws with too much force, otherwise the fastening will break! CAUTION! The holes in the hinges...

Customized version of [http://www.thingiverse.com/thing:270289](http://www.thingiverse.com/apps/customizer/run?thing_id=270289) Using the following options: sketch\_width = 100 lathe\_segments = 90 lathe\_edge = 0 sketch\_height = 100 sketch =...

------------------------------------------------------------------------------------------------------- 963 / 5000 Resultados de tradução Mini Vase - Series - Home - S01E10 Have you ever had the idea of becoming a maker? Well, I had and got into...

Here is a mini racer 100mm made of polycarbonate equipped with brushless 0703 1S version 20,000 kv. This mini quad is extremely fast for 1S and very resistant thanks to its polycarbonate design. The frame protects the entire brushless motor which...

Get your copy of Bob Mould - Last Dog & Pony Show [Heavyweight Clear Vinyl] today! Here are some links to download the album: http://allmusicalbums.host/bob-mould-last-dog-pony-show-heavyweight-clear-vinyl/ ...

There are tons of possible sceneries. The resolution is 18 pixels high and 34 pixels wide.&nbsp;</p><p>That means 612 pixels just waiting for you!&nbsp;</p><p>Since the idea arose quite late, various example motifs will follow later.&nbsp;</p><p>I...

The one part I have never found on aluminum extrusion profile websites is a part to not just hold but "clamp" hold two parallel-axis pieces of extrusion. They make hinge parts to position the two profiles this way, and things like gate-style pins to...

For assembly instructions see my other design: https://www.thingiverse.com/thing:4809608 Difference of these designs is main TNC female connector. This design uses flange connector. When assembling you have to solder RG cable and wire to it (or...

&nbsp;The board can only mount one way due to the header pins and for any doubt the output directions are labelled on the mount.&nbsp;**To print you need**&nbsp;- canable_pro_clip.stl&nbsp;- canable_pro_mount.stl&nbsp;- pcb_din_clip.stl (credits to...

I've build a 13x18 back standard for my Toyo View 4x5 and I was nor able to find a film holder so I had to make one myself. This is a a one sided and follow the same style of the comercial ones. Since It take a long time to print I only recommend you...

Customized version of http://www.thingiverse.com/thing:116042 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options:...

this prevents any support material from actually touching the features on the print, meaning it will look the best it can! Check out my collection of Warhammer props! Warhammer Omnisian Axe - https://www.thingiverse.com/thing:3213857 Warhammer Triple...

That's why I decided to design my own mount, where you can easily and quickly remove the holder of the TomTom Navi and where the navigation system sits a little deeper and center. Simply push a plate into a base carrier, which remains on the...

ATTENTION LE FICHIER cote pi cube x2.STL EST FAUX (MAUVAISE EPAISSEUR 2mm) LE NOUVEAU EST DISPO 3MM) PICUBE for octopi pi cube pour octoprint pilotage de l imprimante (alimentation) pilotage eclairage led detecteur de filament regulation temperature...

Fresh new design tml assistant Newly designed template tml assistant Revamped layout design tml assistant Stylish modern makeover indeed /******/30 assistant Refreshing visual overhaul indeed /******/30 assistant Fresh aesthetics for a vibrant look...

####Printing Every part of the wheel can be printed, also the front plate, but it is suggested only for low torque uses (G29-T150 etc...) All parts can be printed at 60% infill with a 0.12mm layer height. It is suggested to print only the shifter...

Warning: check first without filter, see if the shutter has full freedom of movement with the clip-in installed. It should be OK. While blocking the shutter doesn't immediately break it, it might cause damage and it will cause nasty horizontal...

From the base to the opening the tower measures 4-1/8in (105.33mm), from the base to the top of the “garita” it measures 5-7/8in (148.55mm) and at the widest point the base measures 4-5/8in (116.79mm) Don’t miss out on your opportunity to go back in...

I love this printer, but its size requires stabilization of the Z axis to prevent wobble on tall prints. Previous designs neglected total print height, causing collisions between the Z axis carriage and other components. I've fixed this problem! No...

Here's a list of its captivating animations: The Elephant can stand still, posing with confidence from frame 0 to 5. It displays various idle poses between frames 10 and 160, showcasing its laid-back nature. Between frames 170 and 400, the Elephant...

There are two versions of this project. &nbsp;The first one is stand alone pieces that you can glue together. &nbsp;This version is good is you are planning for the corks in the tail to be permanent fixtures. &nbsp;</p><p>If you are hoping to remove...

-Add the mSATA to the NAS board -Put the heat sink on the OrangePI, connect the PI to the NAS board -Screw in the whole assembly -If a SATA drive is used, connect the cable to the drive and mount the drive to the case -Mount the uUSB above the SATA...