3d models library

Enjoy :) Update 04-05-2021: Adding ender 6 models, upgrading all to V4.3 (slotted mount holes for 2mm height adjustability) and adding "fan duct up V2" which has integrated grill. It's more tricky to print because of the small features so i'll leave...

I've included a Fusion 360 export, should you need to edit the model. A year or so ago, I was having problems with my QNAP TS-563. I needed to get things back up and running so when my troubleshooting was failing, and the device was out of warranty,...

The engraving starts at 1.8mm and the model continues at 2.2mm. Use contrasting colors for a clear reading. <b>note:</b> <i>* If you suffer from corner bulge / swell or an elephant’s foot after printing, carefully sand / deburr them. When...

If you still want to print your own loc line, I used the models from [MinyMan644](https://www.thingiverse.com/MinyMan644) found here -> [Loc-Line Fittings (1/4", 1/2" and 3/4")](https://www.thingiverse.com/thing:3268462). I strongly recommend...

Note: A Honeywell Type H filter is virtually the same size (though not tested with this model) and 3M offers a filter that claims to be compatible with both the Aer1 and Honeywell Type H. 36x rare-earth magnets, disk shape, 8 mm diameter, 3mm heigh...

But 100% fan power isn't necessary, so use an lower Value and take the 100% as "headroom" for bridging etc.The bed leveling is done with an single DC42 IR Sensor (I can highly recommend them).&nbsp;Printing and InstallationAll parts can be printed...

A simple to assemble version of the ER11A Z axis probe that screws onto an ER11A spindle. It has indicator LEDs and can be used to measure and compensate for a bed that isn't flat when engraving, for example a PCB or a curved surface. I use it for my...

Scaling: The model as is in the STLs will accommodate most types of earbuds, however it can be scaled down as much as 30-35% for smaller sets. If you use earbuds with an inline control, such as the ones shown in the pictures, the standard STL size...

...The design is optimized for the given print orientation - no need to rotate the STL model.You will also need two of the strain relief clips, which I have provided as a separate project.Assembly6 pieces of M3 nuts have to be pressed into the plastic.

http://www.thingiverse.com/apps/customizer/run?thing_id=53235 Instructions Using the following options: crankSlack = 1.8 times smaller gear_tolerance = a negligible 0.1 inch midAxisHolderH = stands at an impressive height of 6.3 inches noteAlpha =...

The COMPLETE Swamp Gurunda bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! Swamp Gurunda (Presupported) The amphibious people of the swamps, with slimy skin and innate...

A .3mf file is available along with the STL models.Assembly/MountingThe inner fixture can be held upside-down to desired mounting position for marking the mounting holes. I found it works best to drill a first hole and then insert a screw into that...

It can print without support, and if you have the workflow dialed in, it takes only about 30min per label from start to finish. You might get away with printing just the modell without the support stuff…. didn't try. Depending on your bridging it...

I first encountered the idea for this type of robot in a biomedical article, presented as a potential new candidate for exploring the human colon due to its simplicity and ability to navigate confined areas....

Those are only used to ensure consistency and are not necessary for rendering the model. I also pulled in the 40mm Fan Grill from the Sanginololo case and copied it here to make it easier to find. Those little 40mm fan grills print really nice and...

3 perimeters 7 bottom layers on the cap ( definitely overkill ) 4 top layers Gyroid fill pattern ( any pattern will do ) Extra perimeters if needed was checked Seam position Rear ( make sure the hinge potion of the model is pointing towards the back...

The COMPLETE Bonegnasher Gnolls I bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! Gnolls were spawned by the Demon Raz'n'guul, born from a rotten tooth of the corruption god...

After filing and sanding the bonding surface flat and smooth, and clamping the holders to the shelf with masking tape for a week, these pipette holders have stayed firmly in place for two months with no peeling or drooping.\n\nRedesigned the holders...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

It should be possible to customise the model by changing a global variables that represent the battery dimension and straps width- holes for the LED indicators- reducing the number of screws- creating the cases for wider range of IMUsPlease let me...

2)The plastic for the case is about 0.5 kg (the lantern is large, it was made for a large candle) 3)2 hinges for caskets 15x21mm with self-tapping screws (included, sold on marketplaces) 4)a handle for the casket (you can print it, but I wanted...

This also means that if you wanted to try to build a GoN NERD/NERD TKL, H87a, or the Kprepublic XD87 should all be able to fit - possibly with some small custimization to the model. More to come as I sort this out, but the files themselves are ready...

Yes, there's an actual tank model underneath all the nonsense; it's just badly covered over since I built a spacefuture tank around it. I used a different source for my sponson lascannon; the sponson mount is from Seb's Sicaran proxy, so any of its...

The COMPLETE Dragonpeak Barbarians I bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! The people of Dragonpeaks are direct descendants of the Humans who lived in Aeraunder...

(This is all also in the README)I commissioned prints for these models using PLA with 40% infill and they work like a charm.- You will need to print the Rear Panel if you want to use the parts in the MOBO and GPU folders.- The PSU folder needs to be...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8 custom_top_port_corner_radius...

The COMPLETE Maneater Nagarots I bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! The Nagarots are a cult devoted to the Serpent Demon Yn'aga, herald of the Tyrant-God...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8 custom_top_port_corner_radius...

... Norrick      Details: Gravemaw is standing around 145mm tall on a 60mm customized base. The model is multiple parts, the file contains: 1 x Body 4 x Arms 2 x ½ tongue parts 1 x Intestine 1x Customized 60mm base. ... Support Version Included