3d print bubbling first layer

Furthermore, I provide a test part called "PSUCoverDummy_AllVersions," which you can print and try the fan dummies. You can get the fan dummies here: Fan Dummies On the cover are the names: * 90 = normal 92 mm version * 90R = for the 92 mm rotated...

Therefore, when you choose a spring, its inner diameter should be approximately the same as the outer diameter of the tube.How to usehttps://youtu.be/2PpO4AbOWggThis welder is designed to join the last filament of a roll to a new roll.When using this...

Rafts: Yes Supports: Yes Resolution:.2mm Infill: 5-10% Notes: Rafts and supports are required only when printing the nucleic acid blocks. NGSS, CCSS, and Overview of Objectives: * Describe how nucleotides form specific pairs through hydrogen...

With the use of 7 magnets on each part (fixed body has 7, each changable nozzel also has 7).Press the magnets (neodymium rods 3mm diameter, 6mm length) into the tunnels.Depending on your printing tolerances, you might need to drill the holes a little...

Optional spacers can be printed to ensure proper spacing between GLCD circuit boards as mounting screws are tightened. An optional rear panel cover is provided for use with the GLCD case. The case has holes for up to M3 hardware, but it's intended...

UPDATE 2019-04-26: added redesigned chain for easier print "Chain Whole V3" and fixed bug, both sides needs equal number of chain parts, old design has one missing chain part. Old design for some people fused too much, couldn't get it separated. New...

Below is a guide with very simplified photos in Italian and English versions, and at the end of the article the settings used in print (at least for me.) Good reading. Hoping to have done something pleasant for the community, thank you very much,...

Most of the clock face parts will be identical to those in the Quartz Upgrade, with this design featuring a variation of the clock face (Clock Face w Embedded Numerals) that can be printed in 2 colors where the second color determines the color of...

Love the idea however after printing one out I realised I don't have a 16mm (5/8th) drill bit to make those holes. I've either got 25mm spade bits (which aren't ideal on plastic) or up to 10mm (3/8th). In Australia, most home drills only accept up to...

{"I2CDriver":"7,8,9,10,11,12,13,14,15,17,18,20,24,29,31,36,41,42,44,46,48"} => 13 muss aktiviert sein für ADS1115 (https://smile.amazon.de/-/en/gp/product/B07DFX9Q4G) - Printed Battery Pack, electronic coverage etc.) Teile: 5V Motor mit Getriebe,...

if your endstop position of your head is in the lower left but the print area starts 20mm to the right and 20mm up than you need to set this: ** **#define X_MIN_POS -20 ** **#define Y_MIN_POS -20** **#define Z_MIN_POS 0** **Enable EEPROM settings**...

... using it myself. No guarantees, that this solution works. If you print it, please give Feedback to me and the community (by commenting or posting a make) if the brush works. ... ----------------------------- ATTENTION -----------------------------

The belt path is not flat, and the printed dual belt clips I have here will fail after about 175 - 200 hours of use. I will tinker with the design a little, but what I recommend is to use a linear rail for the X axis. This will also help you avoid...

https://www.thingiverse.com/thing:3589645 Problems: checksumme error while printing from SD-Card at TFT32 #Deutsch# Adapter für Bigtreetech SKR 1.3 zu Anycubic I3 Mega Firmware is for TMC2208 2.0 or higher with UART (ohne Filamentsensor...

The 18 to 22 pipe fitting could be removed This plate could then be copper plated with this technics : https://www.thingiverse.com/thing:1661301 If you have any design to share I would be glad to offer at least the binary codes of the ESP32 and the...

I wanted to fit some lighting to the Kossel so I could monitor overnight prints remotely without having to leave lights on all night. The Neopixel range of addressable strips and rings seem to fit the bill as they only need a single data line for all...

The fireplaces should print without supports (hopefully !). On my Ender, I tried with and without supports; the version without was easier to clean up, and the small amount of looping I got was mostly hidden or (for the stone fire surround) actually...

I liked the idea, but I wanted to change some things: - plastic rolls instead of metal bearings pushing on the glass - position closer to driven rear gears where the force is needed to keep the gears in contact - easy to replace one drum with another...

MegaMAME is a large console which can be stood on a table, or you can use the stand to hook it over your knees while sitting on the couch :-) I had to split the case into two parts to be able to print it on my Ender 6. I'm happy about how it turned...

It is the low-poly and easy to print version of ionic, doric and corinthian columns. Doric and corinthian columns are supportless, only ionic column has some easy to clean supports. Just like chess knight is not photorealistic and just symbolic, goal...

2.6mm thickness - I used something like these:...

The status of the project as of May 1, 2020, is ongoing: 90% design source files (e.g., computer-aided design CAD) needed to iterate on the design mechanically; 80% production files (e.g., STL files used by 3-D printers to make mechanical...

I printed mirrored left and right (screw and wall bracket) so that the unwinding of the coil does not lead to the tightening of the retaining screw, but the screw remains in its position due to the slight resistance. I put a round piece of foam...

Included files: Tower Pro servo mount Clone Tower Pro servo mount Servo horn arm geared (60mm) Servo horn arm Servo horn arm (cap) Faceplate bracket square edge Faceplate bracket round edge Helper arm Helper arm mount for M3 (screw) Helper arm mount...

Two are required, the shape is rotationally symmetrical so only one model is needed, and printed twice. The jig is 2RU (3-1/2") high which is the same as the smaller PDP-11/03 chassis height. To use, simply push the jig into the rack from the...

I printed the attachment upside down, using supports and 100% infill, since it needs to be airtight or nearly so. For the seal, I used Oomoo 30, a rubbery silicone mold compound. Other types of rubber with similar properties should also work. Once...

It really helps to get the belts nice and tight.Here is a link to my BOM, please be aware, this is a scalable design and adaptation may be required, so get more fasteners than you think you need. Parts that needs to be printed more than once is...

Summary: My initial build area was around 80mm; a print requiring more height prompted me to design modifications for increased build height. Upon inspecting my printer, I identified areas ripe for improvement. The result is a heightened build area...

Features Include: 4 Rails Retractable stock Improved Clamping System Very Lightweight 10mm Higher than my previous designs 15mm Wider than my previous designs Ambidextrous Charging Handle Accept a compensator or suppressor Requires a 200mm print bed...

They bite into the print so you can just tighten them fairly snug. If you tighten too much they will strip and you'll need to use a nut but I've used them for years without having to mess with the screws after I got it set up how I want. ... And I...