3d print customizer

I printed mine at a speed of 50, with a resolution of 0.2 mm. Assembly instructions below, assembly photo above. As always, any questions, don't hesitate to ask.Assembly:See numbered photo for reference.During assembly you'll want to keep an eye on...

If you're adding them then I'd recommend printing a few extra as I found the mount pins to be a bit fragile - they're only there to guide you when attaching them. Just a dab of superglue will hold the stack mounts in place. Exactly like the...

Now it can be mounted both ways without clearance issues with the HDMI connector.\r\n\r\n30.06.2018\r\n- Front side v3 with 120mm fan opening slightly reduced to make it fit to the fan inner radius (air tight).\r\n\r\n10.06.2018\r\n- The backside...

So _1_6_10_7 is 1:600000000 or one in 60 million.U1 ArielAriel is the fourth larger of the five biggest Uranian satellites and the second in distance from Uranus, after Miranda. Like the rest of the big moons it orbits at the plane of Uranus, which...

Here are the options I've developed (in progress): | Wire type | Wire direction | Size | Shape | Mount from | Filename |...

***PART #5*** https://www.thingiverse.com/thing:3379068 Are your printer full of dust and small filament pieces, well now it won' get stuck in the slots ***PART #6*** https://www.thingiverse.com/thing:3923876 Do you forget what direction to spin the...

The theory behind combining these two prints is that the stronger frame of the RebeliX printer and the amazing mechanics of the MK2 can be merged to create the ultimate Prusa-style printer. That's our interpretation, anyway. Visit davtr's MK2-X page...

I haven't found the need for much more than the 20mm max height of the print, though I did make a 40mm version just in case. There are two sizes to the soundhole mount. One has a 3mm top clearance and one has 5mm (for thicker guitars, like...

It really helps to get the belts nice and tight.Here is a link to my BOM, please be aware, this is a scalable design and adaptation may be required, so get more fasteners than you think you need. Parts that needs to be printed more than once is...

You’ll need to print the following and its best to fit in this order: If running the V6/Dragon carriage mod then fit the cable retainer and cable into it first, skip this step if you’re not. I’ve included a few options you could use: Cable...

... Note that the edge and corner brackets extend 6mm past the edge of the P5 panels, so make your wood frame 12mm larger than your matrix in each direction. Note - the picture doesn't show all the brackets attached yet because I'm still printing them.

The size works for the 5mm drop or default height, will need to print 2 of them (unless you go with a different cable relief setup, then you won't need them)..As for the x-axis mount, I made it so the endstop sits directly on the mount, and designed...

This design has reduced my purge waste from an average of 200 grams per print down to less than 40 grams. The trick is purging only when a tool change is needed, not every layer like a Purge Block does. On High Contrast filaments, you can increase...

The STLSs are up, I have validated Most of the Prints, but not the barge as of yet. I have done heavy design work on these models, however I consider them remix's due to the heavy amount of various Thingiverse parts, so credit where it is due. The...

For me this is good as it is, it stable anought and easy to print, but who knows, maybe i will change it in future. ... if u have sudjestion for improvement let me know in comments amazon link for screws (not affiliated so i just wanna give u an...

In using the shroud while printing a model that takes up the entire bed, I found that the wires from the extruder need to be routed over the output end of the fan using wire ties, as shown in the new picture above. As I'm using a low-velocity fan,...

Print the "_withbutton" versions of the bezel and frame, as well as the button cap. Insert something squishy (o-ring, piece of foam, rubber band, etc.) between the pushbutton and the button cap. A Raspberry Pi Zero W could be used instead of the...

... (about 7-8 cm each) some soldering skills. **Edit:** Added original adapter battery rail ### Print Settings --------------------------------------- **Printer:** Anet A8 **Supports:** Not required **Resolution:** 0.2 0.32 for the lid **Infill:** 20

material consumption closure pieces are molded at 100% fill for added strength I added the z axis centering device to the et4 base for those who still would not have to use it with a 608 bearing Print settings Rafts: No Supports: No Resolution: 0.2...

That being said, Creality did an exceptional job with the CR-10 that third-party manufacturers can duplicate it using the cheapest, lowest-quality materials available, and still manage to print beautifully with some elbow grease. I say my CTC A10S...

https://www.thingiverse.com/thing:3589645 Problems: checksumme error while printing from SD-Card at TFT32 #Deutsch# Adapter für Bigtreetech SKR 1.3 zu Anycubic I3 Mega Firmware is for TMC2208 2.0 or higher with UART (ohne Filamentsensor...

I have started replacing all of my RPi 4B cases with these while I wait for my RPi 5s.Have also included a number of optional attachment brackets and feet that can be screwed onto the case for specific needs.Print recommendations: - Slice cover...

You’ll need to print the following and its best to fit in this order: If running the V6/Dragon carriage mod then fit the cable retainer and cable into it first, skip this step if you’re not. I’ve included a few options you could use: Cable retainer...

The two silver rings are Dekco and can be printed in PLA. The holder itself in PTEG+ for absolute stability All you need then is a bike GPS mount from Amazon. then an M5 countersunk head, a nut and a snap ring. The 3 original screws from...

... is important! Save with M500. Next, home the printer with G28 and run a bi-linear level with G29 then save the data with M500 and enjoy! Put the command G29 after the home command in your start G-code to level before each print. ... Good luck!

The holes for the banana plugs and the iron holder are not included in the file but can be easily drilled after the print is complete. I did not take photos of the inside because it is pretty crowded with wires; however, if anyone is interested, I...

You only need to print two sets of screws. One for the north celestial leg and one for another leg. The screws have 80mm length and can level at ~50° incline, so a distance of ~40mm. In the middle of the inner screw is a marker that shows the...

The interdisciplinary tasks allow in a simple and fast way a use in the classroom, such as mathematics, Language and general education, but also in the promotion of talent and afternoon care. Print Settings Printer Brand: Prusa Printer: I3 MK3S...

PRINTING ----- Nothing needs supports. I use transparent PLA for everything. I would recommend using the same colour for all mounts, but you could also colour them to match the cap, or code them to the country they come from or something if you...

##You will need: - two MGN12 linear rails 400 mm long with MGN12H blocks - about 16 M4 hammerhead T-nuts (quantity depends on the required rigidity) - the same amount of M4x12mm flat head countersunk screws - about 16 M3x8mm socket head cap screws...