3d print display case

Since I intended to use the printer in an Ikea LACK enclosure I had to make sure it will not crash into its housing while moving during the prints. Sadly the drag chain of the Y-Axis stuck out a bit too much at the back. The rerouted cables give me...

A 0.3 mm nozzle would be recommended for the rotor blade, I printed with 0.4 mm. On the Nabe, drill out the holes for the screws with 2.5 mm and cut an M3 thread. Glue the Labyrinth ring to the Nabe at the rear with CA. Put the ball bearing in the...

... added Arduino program PixelPano.zip to the project. Beware: I am not a professional programmer and when stuff blows up don't start blaming me ! Print Settings Printer: BQ Hephestos Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 mm Infill: 10%

WE don' need no stinking WIRES!!!" As with my other implementations, B-25 Mitchell https://www.thingiverse.com/thing:4121096 Spitfire Mk IX https://www.thingiverse.com/thing:4143803 F4U Corsair https://www.thingiverse.com/thing:4178322 Il-2 Sturmovik...

... would like to have one for your printer please post the dimensions in the comments. When printing the connector part 2 or part 5 support is required, but I had the support in the holes, therefore then used support blocker, pay attention to this

Here is the interesting Part: ; The second zeroing speed when Z is zeroing, the speed is slower M8016 I4 ; ================================== ;;;;;;;;;;;;;;Number of leveling points, ;;;;;;;;;;;;;;;;;;;;;;;;;;The first three parameters are...

As mentioned in the other connectors "thingy pages", there are holes to use 45mm M4 bolts to both lock the conduit inside the sockets, as well as add some compressive force to squeeze the print layers together. Instructions for most-efficient...

I thought about being edgy and calling this v6.66 but I figured a name change would provide a clean slate for the community to build from.Starting with my printed Gecko 1.0, I painstakingly modeled the entire blaster in Fusion360. There were three...

When I printed the holder for the nimble, I realized I'd need to mirror it or change the direction of the extruder so that I could have the Nimble on the right side facing forward. I've uploaded two versions of the same design - one with the extruder...

Leave me a comment if anything needs to be modifiedI preferred to make this support in 2 pieces to be glued with 2 centering studs to avoid removing the tedious supports after printingMarch 11, 2022: Added removable "capuchon amovible V2" which...

old cutting board) Print all parts and cut cfk- and wood rods to approximately 230mm length (measure on the real object before cutting) Put the frame together with the cfk- and wood rods for test and adjust if necessary. Glue all the frame parts...

Its software is very well documented, I had no trouble adapting it to the realization of a printed circuit.(K40_Bed_Software.7z and K40_Electrical_Board)...

I've used this hinge replacement, but it had some issues:It did not restrain the spinning of the cup like the original did, so it was possible to twist off the wire insideIt tended to rub a lot in its socket, thus destroying itselfAfter replacing...

To solve this you could pause after first hex layer and check hole width, or if you have a MK3 magnetic bed, you can take it off and pound the nuts in with a hammer (make sure you have a well anchored bed on this print!).\r\n\r\nThis actually...

For instance, replacing the current flexible-tube-and-nozzle solution with a printed double-hinged air duct (directing air from the side) could change position and orientation of the pipe end opening to the front. Adding support for a second nozzle...

However, the vast majority of ripped files from MWO are not optimal for printing, and while many other modelers are content with stitching these files together to make something workable, I decided to take it a step further.   Instead of just giving...

Lastly I have removed the wildcard hole on the back and replaced it with an angled slot for another scraper, a generic single-blade razor holder that has been useful for fine detail work or prints that are very on the bed. I picked it up on a whim...

Once you are happy with it, install the switch - If you print the grip, make sure there is enough room for the LiPO and you have a mounting hole as well as the wiring hole - I used 18awg main battery wires, and 20awg for the solenoid. - To make the...

This will be an *extremely* tight fit, by design, and will likely require a fair amount of pressure the first time an end cap is installed.\r\n* Drop a spring into the spring cup of the end cap.\r\n* Push the rail toward the idler side of the printer...

Mine is inspired by a number of different dry box builds and parts, including:Sterilite 20qt Filament Dry Box by StvPtrsn on ThingiverseAngled Dry Box Feeder with Source by Bolukan on ThingiverseFor this build you will need the following parts:17x...

Print Settings Rafts: No Supports: Yes Resolution: 0.2mm Infill: 100% Notes: I used concentric supports at 30% with a 0.5mm gap, it supported it great and fits perfectly Installation When installing, remove the spray nozzle on your aerosol spray can...

Leave me a comment if anything needs to be modified I preferred to make this support in 2 pieces to be glued with 2 centering studs to avoid removing the tedious supports after printing - March 11, 2022: Added removable "capuchon amovible V2" which...

Recently printed the Hero Me Gen 5 for my setup (the modularity is incredible) and noticed a few misaligned holes/notches with the Printermods.com MDD V1.3 for Ender 5 (unsure if designed/aligned perfect for MDD V1.2, Printermods has now released the...

It may seem complicated at first but becomes easier after playing around with the panels (and printing off many of the different types). The reinforced cube structures can also be expanded to any size, but they are more difficult to build, both...

If you are going to push more than 15, you really need to step up and redesign for 20+ amps....

In the photos, you can see I'm storing extra sleeves in the upper-right slot.The labels on the deck boxes were custom made, using Print-and-Cut on a Silhouette Cameo, and JandJPackaging Glossy Vinyl Sticker Paper, available on Amazon. (I use a Canon...

(Please remember that those tiny bits, like little pieces of fruits, are offered in a very small scale to fit well inside the glasses, and they should not be printed separately without scaling them up) 4. TAVERN FOOD, Part 1 SNACKS (12): chip,...

I chose vertical slats here instead of matching the OGS horizontal mainly for ease of printing without needing supports, and also because trying to match the size and spacing of the OGS vent and not block them would be a pain, so I split the...

I wanted one that * is cheap to print * handles spool rewind for my mmu2s * doesn't need me to order loads of other parts (i already had the rollers from the prusa mmu2s trays and the bag from my prusament which is most of the parts) * fits on my...

Since I don't use these hooks for heavy loads I printed mine in PLA with a layer height of 0.2mm. I recommend using at least 3 contour lines for rigidity. If you want to hang heavier things I suggest using PETG or ABS and a layer height of 0.3mm...