3d print engine

... can be found at https://github.com/dewhisna/TB6600StepperDriver and boards can be ordered from https://www.oshpark.com/shared_projects/tKN4X7AL. Print Settings: Printer: FlashForge Creator Pro Rafts: No Supports: Yes Resolution: 0.2 Infill: 35%

A friend who recently lost a finger in a woodworking accident contacted me, asking if I could print Mat Bowtell's brilliant "Kinetic Finger" for her. During the process of printing, assembling, and testing the device, I came up with some improvements...

Printing them flat gives a rougher tile surface but is quicker and makes for stronger clip holes. None of the parts need supports, but adding a brim helps prevent warping (I had some adhesion issues at the time). As a self-proclaimed anorak, I...

The smaller Knob is one from radio shack that Ive had for a while, there are other examples you can print elsewhere on thingiverse 2. Keycaps are [YDMK SA Carbon blanks from Amazon](https://www.amazon.com/gp/product/B07PZRSZZS/) 3. LEDs: a. On the...

Once the speaker housing fits into the mount correctly reinsert the metal clips to lock in place, there should be a small groove in the stem on the printed housing that the metal clip can slide into.Trim new speaker wires, leave enough slack for the...

Since Creality systematically refuses to supply Sermoon D1 customers with spare parts of parts subjected to natural wear, such as Hot End and simli, having some problems with the original, I decided to re-build them, improving them to obtain a...

:) Suggestion : print the knobs with a different color from the extruder itself, it'll be more fun. ;) VERY IMPORTANT! You must set the following variables in the Configuration.h of your Marlin firmware and recompile/upload it, otherwise your new...

(My parts are printed in PETG, choose a glue that works with your filament material.) [Bill of Meterials] Mechanical Parts you need to build it: 1 piece - Tin Can 3l approx. 160,3mm the ring up and bottom is approx 162,5 and the thing is approx 183mm...

That is to say, it should work perfectly fine without the wrap, just doesn't look as snazzy. The wrap should have a diameter of 28cm and thickness of 10cm (you might be able to get a cheap one for a normal sized wheel, cut it and sow it back together...

By default, all connector sockets are drilled at 45 degrees to match Joe Larson's base blok and allow printing without needing supports. The top face socket can be set to any angle without support issues, but a socket at another angle on any other...

As you likely won't be able to buy parts in "singles" print a few of these to make more around your home and or give to friends. Should still come out cheaper than buying one of the branded versions and will be batteryless with more virtual walls...

When mount wears off due to friction the magnet holds the switch down and provides some threshold so that it does not go down on its own. How to assemble the tabs: Use file on the inner edges of mount or remodel it according to how accurate your...

Its originally for compressing the original rubber prop around the pee hose to hold it in place but on my printed part its just for show but looks rather nice IMO. Second, the Harbor Freight magnet isn't super strong and the connector has a tendency...

https://youtu.be/58YBYkTr3eM UPDATE 2017.02.02 This project has evolved into http://www.thingiverse.com/thing:2081258 Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator Z18 Rafts: Yes Supports: No Resolution: High Infill: 0% Notes:...

De esta forma queda todo más ordenado, accesible y fácil de sacar a mesa. Cada caja tiene el nombre del arquetipo correspondiente para identificarlos más fácilmente. He añadido además una tapa sin nombre para que cada cual ponga lo que quiera. Print...

So _1_6_10_7 is 1:600000000 or one in 60 million. S13 TelestoTelesto is a small moon of Saturn, orbiting in the same orbit of Tethys 60 degrees before the bigger moon. This point of relatively stable orbit relative to two bigger objects is known...

Included within each .stl is the main pack and a circular connector to attach to a Stormtrooper body, these will need to be merged before printing. These are mainly meant for kitbashing digitally, so they might not work with existing citadel...

Here's what you need: * Hemera with square Nuts inserted in all 4 Holes on the correct side * 4x M3x8mm for attaching the E3D Hemera to the Connector (don't use longer than 8mm screws!) * 2x M3x12mm for locking the two parts together (can be a bit...

3 - Significantly stiffens the LEFT hand side stepper motor mount - the standard plastic one flexes a tiny amount when printing - not badly admittedly but this bracket is much stronger 4 - Corrects the Belt geometry - the factory standard setup has...

I enclosed an stl file just to get the thing viewable within Thingiverse, but of course it cannot be printed at least due to its size. Please, do not criticize. Another note to the FreeCad file - it is not cleaned up, so a bit messy inside, will...

In order to prevent dust and dirt particles as much as possible from coming into the slider channels of the S22 Pro the aim is to close off the beginning and the end of the sliders from particles, however you also don't want to introduce friction and...

-many parts resupported with improved orientation -lower rear hull was rebuilt for better printing and assembly -reorganized file structure Lore: The Renault Pattern Light Logistic Hauler (aka: Renault Pattern Cyclops, or Shovel Schlepper) is a...

I had to print this new base a total of 4 times, making adjustments along the way until i got it just how i wanted it and holes in the right places with enough room (for usb cables to plug in properly for instance). The next piece to this, was...

TEST THEM FIRST - print just a few and see if they fit. I had to fiddle with the sizing quite a bit, and the insert files included work on my printer with the bases that came with my Orks - your mileage may vary. There are two types of movement...

When I printed the holder for the nimble, I realized I'd need to mirror it or change the direction of the extruder so that I could have the Nimble on the right side facing forward. I've uploaded two versions of the same design - one with the extruder...

I need the length and width of the car base as shown here: https://imgur.com/5T6mb2LThe display base is separated into 3 parts for easy printing and colour swap. The parts are:1) Name...

I wanted to use a saddlebag and without a protection the bags would just keep banging on the motor. But what I consider the most needed addition to the original project was a anti torsion bar. The number 1 frustration I had so far was correctly...

Please see the pictures for individual printing instructions. If the spur gear for the table binds when rotating the table, loosen the stepper bolts, push the stepper inwards, and tighten. 50% or more Infill for all parts. Video showing this...

With your purchase, you are licensed to print unlimited copies of these files for personal use. I'm a solo artist with a nasty caffeine habit, though, so please don't share, trade, or give them away. Commercial printing is done under separate...

Since I intended to use the printer in an Ikea LACK enclosure I had to make sure it will not crash into its housing while moving during the prints. Sadly the drag chain of the Y-Axis stuck out a bit too much at the back. The rerouted cables give me...