3d print engine

I added a calibration spiral and scaled it for printing. Attention: my firmware has been modified for me; it is crucial to edit and define the printer options, DELTA_HEIGHT and DELTA_DIAGONAL_ROD. Note that the motor directions for my TMC2100...

Components used: 8 x 9G Servo motor - Link: https://www.banggood.com/TowerPro-SG90-Mini-Gear-Micro-Servo-9g-For-RC-Airplane-Helicopter-p-1009914.html?p=E01411629100201406T1&custlinkid=359550 1 x White LED - Link:...

I'm currently printing 3 perimeters, 6 end layers and cubic infil which has the advantage of forming lots of sealed pockets. To get the cubic infill strong enough I've gone to 30% infill, partly based on one of the Gong designer's youtubes where he...

... click the "like" button. in that way I will continue sharing more things. If you print one I would love to see it in the section "i made one" of course, all views and advice are welcomed, you can always improve design.. ... thanks for watching

This was printed on a Flashforge Guider II, High Quality, so the tolerances are good, but I also allowed a 1/4mm tolerance between parts and at this level of quality, it gave me a good fit. Painting it was using acrylic spray, primed and filled,...

# Print Instructions: Be sure to use supports for the wall pin and the gun holder. Take care to clean the supports and leave a smooth finish on the gun holder. I set this up so the gun points to the right to hide the screw holes. If you want to...

I printed mirrored left and right (screw and wall bracket) so that the unwinding of the coil does not lead to the tightening of the retaining screw, but the screw remains in its position due to the slight resistance. I put a round piece of foam...

# Print Instructions: Be sure to use supports for the wall pin. I set this up so the gun points to the right to hide the screw holes. If you want to point it to the left, just mirror the gun holder and adapter plate. (I didn't test it, but I'm...

... no claims on how well the design is structured... I'm still learning the application. Print Settings Printer Brand: Creality Printer: Ender 5 Rafts: No Supports: No Resolution: 0.2 Infill: 10% Filament: iSANMATE PLA Black Category: Electronics

The V1 frame weighs about 10g, while the V2 frame weighs around 8g when printed using PLA. My entire setup (currently based on the V2 base and the V1 top) weighs roughly 38g without the battery. It is specifically designed to support motors measuring...

To save time and money, I need to print new blades regularly. === SIMILAR STAFF === My search on Thingiverse led me to this page: https://www.thingiverse.com/thing:3025985 As a difference from olavl's design, I sketched one blade and rotated it...

I have design it in order to be printed in a 200x200 mm printer (the most common). Everything is my own design exept the front lights which I have to thank to my friend Cooperino who make a fantastic desing work =D. I've tested the model and,...

I also added a small electrolytic capacitor to stabilize the power to the ESP32 to prevent low power brownouts, 47uf / 50vdc - More than a than...

# Print Instructions: Be sure to use supports for the wall pin and the gun holder. Take care to clean the supports and leave a smooth finish on the gun holder. I set this up so the gun points to the left to hide the screw holes. If you want to...

The system interacts with an on-device embedded webserver, and I've used the same prints for multiple brands of blinds.\r\n\r\nCheck out the pictures and animations showing how it all fits together.\r\n\r\nI previously had two code bases for MQTT and...

I took the original part and modified to make it a little simpler to print and also design. There is draft in original part in two directions of the part for molding purposes. I removed the vertical draft but kept the fore-aft draft (which is...

... amélioré : plus esthétique (et d’autres éditions spéciales;) ), système d’éclairage led, etc. Pour suivre ces améliorations, n’hésiter pas à vous abonner a ma page Thingiverse et Facebook : https://www.facebook.com/waikikiprod Bon print à tous !

# Print Instructions: Be sure to use supports for the wall pin and the gun holder. Take care to clean the supports and leave a smooth finish on the gun holder. I set this up so the gun points to the right to hide the screw holes. If you want to...

... and I think it is pretty intuitive, but if you have questions, I'll be happy to help out. Be sure to block supports in the zip-tie channels. I recommend printing the blower ducts in PETG, if not ABS, due to the close proximity to heat. ...

Print the surfaces 6mm thick. ...50% infill PETG This chain roller fits a lot of Yamaha Dirt Bikes and ATV's: Part # 30X-22178-00-00 Yamaha Motorcycle 2009 WR250F - WR250FY Frame Yamaha Motorcycle 2013 WR250R - WR25RDC Frame Yamaha...

Our design is nested and compact, which means it takes less time to print one set. The board we use makes wiring and assembly more accessible. With an internal battery charging circuit, you don't need to remove the battery for charging. To control...

I printed this with PLA on my prusa mini with supports on the build plate only, 40% infill, 4 perimeters. for the support settings I used: Z contact distance: 0.2mm pattern spacing: 3mm contact layers: 4 xy separation between an object and...

Here is the rewritten text in American English, without any foreign characters, and with a Flesch-Kincaid score of 100%: Here's a simple drying box for your filaments to make: Materials list: * 3 pieces of plexiglass, 350mm x 350mm, 4mm thick * 2...

Edit 11/12/2019: I printed it out and it fits very tight, so you don't need to use anything to hold it in place. I saw a mistake somewhere and it's shorter than the original, but if you need it longer, you could edit it in the .ipt data. In my...

For the same price of one tent pole could buy 2 x 6.5m lengths of Al tube, and a roll of filament. Took a few attempts but the twist lock cams were very easy to design and print and worked far better than expected.  The larger version...

This uses the same roller/spacers as the lower guide, so just print two sets of those. ...There are four machine screw holes (use them with 4mm screws and T-nuts), you only really need two of them, the extras are in case you want to move it further out...

I am in the process of test printing with this setup. Edit 9/29/21: The Extruder mount bracket may not be needed if the three bolts are replaced with 3x M3x35 bolts. The adapter should be tight enough inside of the V6 adapter. Edit 9/30/21: I...

... Note that the edge and corner brackets extend 6mm past the edge of the P5 panels, so make your wood frame 12mm larger than your matrix in each direction. Note - the picture doesn't show all the brackets attached yet because I'm still printing them.

I have added another screw hole to it, but haven't printed or mounted it in that configuration yet, so hopefully the glue isn't required anymore. - Cap - to cap the bench mount suction when I am using the vacuum as dust collection for the other...

After printing the mount, you may need to widen the opening for the magnets with a 7mm drill - since the magnets I used are 7.1mm, they hold very well within the holes without any glue necessary. The bottom of the Sidewinder is made of steel while...