3d print file

These values are likely intended for a custom PCB (Printed Circuit Board) stencil that will be used to transfer circuit elements from a copper plate onto the actual PCB. The `ncustom_` parameters suggest these values are specifically customized by...

The electronics are easy to set up and print, with no glue required. Simply snap together all the parts except for the bottom lid, wire the LED to the ESP8266 board, and you're good to go! Here's what you need: * An ESP8266 microcontroller:...

Print Settings: * Printer: Folger Tech I3 2020 * Rafts: No * Supports: Yes * Resolution: 0.2mm * Infill: 20% Notes: The numpad's bottom covers have a slight angle to ensure they fit perfectly when facing the correct direction. Securing Threaded...

The downside to mounting it on either axis is you lose a slight amount of printing area on said axis. As I very rarely use the full height, I thought it was a better option to use it as it was designed. I couldn't find a bracket, so I remixed...

Can be printed on common 220x220 plates like the ender 3 v2 Check also the Premium optimized versions for 30-50-80-110 LBS motors! If you need a custom propeller for your motor, contact me on instagram/facebook: sapolab_diy If you found this object...

The small holes on the printed parts can be used to screw them into the shelf for added strength. Some helpful tips: - The two parts of the cross-brace are riveted together. The metal is extremely soft - any electric drill will make short work of...

The pics are of an earlier version and I will update them when I have the final version printed. Parts required: * 2 x M4x16mm Socket Head Screws (M4x12 would probably work as well) * 2 x M4 lock nut * 2 x rubber bands (regular size) * It will also...

You will hear loud clicks, see shifted layers and/or thin gaps in the printed model. Consider getting a longer PCI Express power cable instead, e.g. NEW male to male 6 PIN PCI EXPRESS Y SPLITTER POWER CABLE--12" MADE IN AMERICA or 6-pin Mini to 2x...

And you can keep it all together, and test out different control ideas, by using Electroblok!You will need:Braccio Robot Arm https://store-usa.arduino.cc/products/tinkerkit-braccio-robotArduino Uno https://amzn.to/3zMtg2wJoystick Controller:...

I printed two additional gears from here but the teeth didn't mesh properly with the small gear. Part of the problem was that my small gear was also worn down. So I made both gears with the correct tooth count and pitch and they mesh correctly. The...

You can find the exact product I used here: https://amzn.to/2CIuwsG To print both parts, use no support. I recommend a 3x3x3 .2mm grid with 25% infill in both directions. I experimented with .24mm 3x3x3 and 10% infill grid in both directions, but...

... The mask can be printed using different materials (PLA / PET-G / ABS / ASA / TPU, etc.). For information on the effect of 70% IPA and UV sterilization on various material types, refer to this study: https://www.youtube.com/watch?v=txrXX0CQHhU&t=1s.

Happy printing! :) Parts Description: 1) Basic Connector - Puts two pieces of track together 2) Basic Connector w/ 2.5mm hole - Puts two pieces of track together and has a 2.5mm hole in the center of the button to allow you to mount it...

This snowflake ornament was printed in white PLA at 200C and the printbed heated to 65C. Don't forget <a target="_blank"...

2022-08-13: If you want to buy a print of this part, check out my new Etsy shop!: https://www.etsy.com/your/shops/DynamicSolutionsCA/2022-06-05: Replaced the models. The outer part is now thicker and the inner part is thinner. The edges of the...

A few things to know: You may need to do some sanding on the Body Back so that it slides closed, depending on your print tolerance. You're going to need a MagicBand+ The Batuu Bounty Hunters game does not work with the older Magic Bands. Any...

This upgrade addresses issues related to printing flexible filaments. Key differences between this and the standard guide are: 1. The original guide features a 5mm diameter conical entrance that meets the PTF bowden at a depth of about 7mm,...

screw the rod tightly, put the printed cylinder on and screw the bearing with the screw on the rod on the other side (without the old big washer). 4. screw everything tightly, thus the bearings are pressed into the cylinder 5. disassembly:...

... perpendicular through-hole for that other zip tie mentioned above. With the addition of the flange, printing without supports is not possible. ...I recommend turning on supports only where they touch the build plate in Cura instead of everywhere.

Print two copies of the flange, you will need to orient them so that screw holes line up when installed. The flanges are sized to hold the blower intake manifold & filter core tubes. Secure them on installation by drilling a hole & adding a screw...

To assemble this version: Print one TOP part, one BOTTOM part, and two WHEEL parts. Carefully detach the covers from the sanitizer and remove the driver board. Remove unsoldered lamp leads and battery terminal wires. Insert the reflector/lamp...

The printing is very simple and we recommend it with PETG since the extension of the funduct is very close to the nozzle and it will receive a lot of heat. We use supports only in the back, we leave a photo of how it is placed on the bed and how...

For a complete set, you should print 5 of the 7 coins version (red/blue/yellow/orange/purple coins) + 1 of the 5 coins version (Shield coins) + 1 of the 4 coins version (green coins) + 1 optionnal rack to keep them tidy. Warning: the Splendor...

If you want to adapt this design to a non-Wilson II printer, I'd be happy to help with modifications based on your specific dimensions.\nThis will allow for clear access to the adjuster screw and potentially recover some lost Z Axis height.\nThe hole...

Print the upper part and lower part twice each. I used ABS with 100% infill. 4. Remove the original middle or upper headstraps. The design does not work for extending the lower headstraps. 5. Remove the triangular clip around the mask's...

There are also two bolt locations for the wheels to adjust the height, or you can even have a single centre wheels instead of pairs of wheels.The handle bracket design is for a 25mm broom handle, however the model does contains some spacers as I am...

Print with at least 4 walls and do not reorientate the models, supports touching bed is required, do not use add supports everywhere. There are 3 different versions of the fan shroud, one for a Creality factory hotend fan with the wire on the...

Print Settings Printer: bq Hephestos 2 Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 Infill: 50% or more Notes: I used Brim (20 lines) and had supports for the rounded corners on the bottom of the box and inside of the screw hole. Set the...

... Fractal Node 304 ITX case. I'm reusing the Corsair H90 with 2 x 140mm Noctuas in a push-pull config, and underneath that is a 120mm fan used as intake for the GPU. Please excuse the horrible print quality in the photo, my printer needs an overhaul!

With some base textures the difference is negligible (between the 25mm ones) if the texture doesn't have much definition, but I've included them for the odd chance that is exactly what someone needs.It's probably best to print these with a resin...