3d print playstation controller

I added a calibration spiral and scaled it for printing. Attention: my firmware has been modified for me; it is crucial to edit and define the printer options, DELTA_HEIGHT and DELTA_DIAGONAL_ROD. Note that the motor directions for my TMC2100...

Manifolds pictured were printed using nylon 6,6 weed-whacker line because that's what I had on hand that could handle heat and chemical exposure. I believe ABS/ASA would actually be a superior option, as you could use acetone to seal and fix the...

How to make You can print all parts without support. Place on the build table as supplied. Circuitry is exactly as same as former thing named "Minimal Mechanical Digital Clock with Network Time Acquisition", https://www.thingiverse.com/thing:4931539...

A custom DIY rear light for the Patton.I wanted a solid red light on my Patton that didn't blink all the time and also increasing the visibility overall so I designed this mount for a 5V neon led strip which doesn't require data just positive and...

Preparation * Print the puzzle components * Have phones or tablets with the Aurasma app installed * Provide students with 20-25 minutes to solve the puzzle References The math involved in this puzzle is relatively simple, so no references are...

A VESA mount is included with the Intel NUC, which you'll use to attach the NUC to the new printed plate. The NUC doesn't come with a screen. I use a 7-inch capacitive touch screen from Amazon, specifically the GeeekPi 1024x600 model. You can find...

I recommend using technical skills to assemble it, but don't worry if you're not a pro - it's still easy to print and assemble. You'll need some common 2.5mm screws, but make sure they're short enough or use small ones (5-7mm long). Alternatively,...

... click the "like" button. in that way I will continue sharing more things. If you print one I would love to see it in the section "i made one" of course, all views and advice are welcomed, you can always improve design.. ... thanks for watching

Steps: - Print the file - Slide the PTFE into its location at the desired length - Use a felt tip pen to mark the start of the contact on the tube - Take out the tube and cut it round on the outline as on the attached renderings - Replace the tube -...

Everything looked good in the preview but when I printed them they were just left out. I solved this problem by increasing the thickness to 0.5 mm.</p><p>I added a 1 mm wide bar in the middle of the switch to make it easier to move the switch when...

This miniature comes with optional presupported files for resin printing. These files come as ready to go STL files or Lychee files if you wish to edit the supports for your custom needs. You can find my latest releases over on my Patreon!   Agannon,...

If you use Marlin, you could set in Configuration.h: ``` #define X_MIN_POS -15 #define Y_MIN_POS -15 ``` Print with ABS or with any rigid plastic which works in your temperature range. Take into account that the mount contacts the stepper motor which...

UPDATE: I have reworked the top and bottom of the case so that it can now be printed without supports being turned on. I have also moved the USB and Ethernet port partitions to the top half of the case to ensure their stability when installing the...

... the key « f » for fillets.</p><ul><li>Draw a sketch an the top circle under the helix with a little rectangle who will « join » the eagle wings. By doing that, you will have a better print by having less retraction.&nbsp;&nbsp;Category: Automotive

This print took me about 17hrs on my Creality CR6-SE as I wanted it to be super solid and smooth. This palette is made to fit a 3-layer storage container from walmart...

The other must have mod is the welding mask, I was able to unsnap some joints on a $10 mask and 'thread' it through the existing holder, then just use the top Velcro strap to attach to the front headband, better than a printed attachment - takes all...

As the buttons require minimal material, I recommend printing a set of each style to ensure a perfect fit. It is easier to solder all wires to the boards before permanently mounting them in the box. By connecting the common pins on the buttons...

Simple little print and fits great. I use the L6-30R boxes for my mining computers that are on a 240v 30amp outlet, Plus I have a 120v Lid I designed for a square outlet. When you use the outlets you need to trim off the tabs a little to get...

I calculated that the production didn't justify the cost of printing the 402 parts for the space rocket and made the decision to have them laser cut out of plexiglass. Then, I ordered all the straight parts (1HSP to 5HSP) to be cut out of plexiglass...

: Original Model: http://www.thingiverse.com/thing:2105057; EZ Print Model: https://www.thingiverse.com/thing:2153317; Lazy Susan Base: http://www.thingiverse.com/thing:2186716. Both Models Are 100% Compatible with This Gearbox (& the 66.46:1...

To achieve this, you can adjust your printer using the following template: https://www.thingiverse.com/thing:5413456 It allows you to adjust the feed rate specific to your filament to obtain precision of the order of a hundredth of a millimeter,...

Later I will add photos of a finished print with some painting and post-processing tips.See the Remixes section for two other variants.-------------------------------------------------Tento bunkr, tzv. <strong>řopík</strong> (podle ŘOP: Ředitelství...

Printed with CR PLA at 60mm / second 0.2 layer height with 0.4 nozzle 205 ° C hotend 60 ° C bed temperature 100% infill with tree support 45 ° --------------------------------------------- Deutsch: Dies ist ein Remix des Pi Drawers. Leider hat das...

... so I installed three spacers. His desk is now rock solid. It actually worked out pretty well.Print SettingsPrinter Brand:CrealityPrinter: Ender 5Rafts:NoSupports: NoResolution:.16mmInfill: 100%Filament: Overture PETG White   Category: Office

Scan the sheet using a geometrically accurate scanner (for example the ScannerPro app on iPhone making sure geometry correction is enabled.). Follow this youtube guide to import the scanned image into FreeCAD and trace the contour of the lens. Pad...

I also appreciate pictures of your prints too. Thanks ;) NOTE: A new V5 lightweight and mini version is available from: https://www.thingiverse.com/thing:4850894 LEGAL DISCLAIMER: This device is designed for adults. Long term wear can suppress...

(I would definitely suggest retracting when fitting the slider as it is a tight fit, and you could damage the tip of the wiper during assembly) I then recalibrated using raw data, and it is very smooth and accurate I printed this upside down with...

This is done by a diffuser glas which is printed in clear PLA and does the job quite well for me. In my version I used four industrial 3W LEDs, but I also designed an adapter which you can modify to your own needs and put all kind of LEDs on. If...

...Both parts are easy to print without support structures. For reinforcement, the part to which the pool pipe is attached with screw clamps has a reinforcement. The hole in the container is approx. 45 mm and was actually drilled for the rubber sleeve.

This kit is presupported, but also includes unsupported STLs for those who want to print in FDM or would prefer to handle their own supports. ...If you feel inclined to support my work (and get access to previews of upcoming work and voting rights to...