3d print topographic map

I wanted to add lighting to my Kossel so I could monitor overnight prints without leaving lights on all night. The Neopixel range of addressable strips and rings seemed perfect, needing just a single data line for RGB control and a 5-volt supply. At...

**Gravitrax Ball wheel V2** - Difference in height 80mm - no support necessary - 3 pressure parts: wheel, gear, pillar - Printing time approx. 8 hours - it is required: (motor see links) 1 x M5 screw 50mm or threaded rod 1 x M5 washer 1 x M5...

While I haven't printed it myself, it should work just fine. *** 9/27/18 *** The main litho no longer needs to be resized (I've renamed it to MainMashup.stl). The crown's orientation has been fixed, and all the parts should fit nicely together now....

Go ahead and try it out!Edit (4/5/2019) I've included some tighter tolerance sleeves to help them stay together without glue.Edit (4/11/2019) I Have replaced the V2 Generic Race Cartridge and Sleeves with CORRECTLY oriented for easy drop&print, I...

After numerous requests, I also included the Z-probe for the Bl-touch in the gallery photos.Below is a guide with very simplified photos in Italian and English versions, and at the end of the article the settings used in print (at least for me.) Good...

FYI, I am using an FDM printer for the base unit and anything that pops up through the pie panels I am printing in resin. Here is a video link of my electronics mock-up: https://www.youtube.com/watch?v=h6nXO9jEetk Base Unit Lower Limit...

To save time and money, I need to print new blades regularly. === SIMILAR STAFF === My search on Thingiverse led me to this page: https://www.thingiverse.com/thing:3025985 As a difference from olavl's design, I sketched one blade and rotated it...

different clamping nut sizes.And this is the result of some drawing and printing.• Part 1 is the mounting plate suitable for all diameters of clamping nuts.       This is mounted on the tool-holder plate using the hole in the plate to secure and an...

I recommend printing the monorail at 100% infill. The sign can be added into the right ear from a slit between the ears. The sign is based on the one that was on the Epcot Ball from 2001 to 2007. The sign was modified to add in open area below the...

Print Settings Printer Brand: Printrbot Printer: Simple Red Supports: Doesn't Matter Resolution: 0.2 Infill: 20 Notes: Use supports touching buildplate on the legs, gimbal plate, and top plate. ... Custom Section This is the gimbal in action...

FR Tournevis compact avec chargeur 8 têtes à rétention magnétique. 1 aimant cylindrique de 1 cm x 1 cm est indispensable pour le fonctionnement du stockage intégré au manche l"aimant est en contacte avec la base de la lame porte tête ce qui permet...

... supportless.   Files are for personal, non-commerical use only. Please help support a small business and fellow gamer -- do not sell or distribute files or sell prints. Please see the STL Licensing Agreement for additional information. ...Thank you!

The bucket of the catapult was created using a Dremel 3D20, printing it out of PLA. How I Designed This Design Overview The catapult was designed to come together like a puzzle and have connections that require no form of fastening. It can be...

If you're using a servo, be sure to print the rev counter (“rev_counter.stl”) as well, and mount an extra magnet and an extra reed sensor in place. However, if you use a stepper, all you'll need is an extra coupler for it to work smoothly. For ease...

Stuff you'll need: Nuts and bolts: 3x12 2pcs (optional) 3x40 2pcs 3x30 4pcs 3mm nyloc nut 8pcs 5mm nut for GoPro mount (optional) Self-locking strap with a 20mm strap or velcro 5mm cube magnets (1or2) (optional) Instructions: Print (obviously). ...

... in and out you can select the top_cover. -- save -> rendern -> STL export -> close - Repeat the steps, to create a new picture frame layer, to stack this. - print all generated stl files. ... - To attach the modules via 1,75mm Filament and glue.

Everything is designed to print without supports. This project is a work in progress, but current state is usable.Spool Assembly:Attach tie to desired slot. I have found the slot opposite to the hanging hooks tend to position the cord ends in a...

A long cord of ethernet cable carries power from the output of the DPDT relays up to the geared motor where all the printed parts and mechanical components are. Ethernet has 8 wires, so use 4 pairs to input +/- and -/+ into the motor. Again, refer...

Maximum temp limit should stay under 260C during any time print takes while using this setup but please take precaution before attempting operation near temperatures much higher. Instructions: Upgrade with modular thermistor installation...

Print at desired size and use to keep track of your ammo clips. 5 is the maximum on this D6 (The Logo counts as 6 for normal dice rolling) and each set of rounds points to the next lower, making it easier to 'count down' the dice until your clip is...

Manifolds pictured were printed using nylon 6,6 weed-whacker line because that's what I had on hand that could handle heat and chemical exposure. I believe ABS/ASA would actually be a superior option, as you could use acetone to seal and fix the...

To achieve this, you can adjust your printer using the following template: https://www.thingiverse.com/thing:5413456 It allows you to adjust the feed rate specific to your filament to obtain precision of the order of a hundredth of a millimeter,...

You will greatly simplify the assembly on the Enclorure.Insert the Lid_lock_V2 into the frame_front_V2 and mount on the Enclosure (each of the front parts will be attached with 3 M3x4 screws)assemble and mount the hinge according to step 6 - 10 of...

I added a ziptie location for the cables (break off the designed-in support), modified a ton of tolerances, got the fan ducts adjusted to the proper height with the nozzle, made a permanent BLTouch mount, embossed "CR-10S Pro V2" and "Micro Swiss...

Print that inner panel whatever color you wish and use white LEDs to shine through, or any combination of plastic colors - LED colors, color shifting, or controllable I use two buck converters like intommy does, but with a slight difference. The...

* magnets (only needed if you also print the door brace) [link](https://www.amazon.com/gp/product/B07842PSJD) _____________________________________________ STEP files are included, but contain some parts that should be hidden, couldn't figure out...

This resulted in wasted project time as it was a 32 hour print. Therefore, I started thinking: could I turn this into some kind of jam sensor? The answer is yes, you can. So I set out on my mission to upgrade the Filament Bot. First let me say, my...

Note that possible dents in the metalbox could make it fit tighter / harder to push the holder in or pull out.You have to print two holders (2x top + 2x bottom). This fits 48 batteries in total.<br>&nbsp;</p><p>I designed the hight of the holder in...

G-Code Generation: The G-code files have been sliced using Slic3er, optimized for printing on a Prusa Original i3 MK2. SCAD File Information: The SCAD file generates all three parts of the cabinet. To select the desired part, navigate to the top...

Printing is straightforward and there's no need for supports (except for the diffuser), any spans should be OK without them. There's a little slack to allow the diffuser to fit. If your tolerances are a little out, and the face isn't tight in the...