3d print watch

There is a bonus version for those who can print multi-material with a Zelda Triforce design. While the two hooks on the sides do a great job of keeping the handheld secure, the hooks on the bottom and top needed slight tweeks. The hook on the bottom...

Take a look at my hinged cable organizer to manage those pesky cables as well: https://www.thingiverse.com/thing:4640618 Copy and customize it on Onshape:...

... Fusion 360 file is included. I apologize, it is a bit sloppily modeled but the project was initially created to just model and print some test-fit bits for the entire project and ended up encompassing the whole thing. ... Hope you find it useful!

Added calibration for cyclic, to counter for printing settings/assembly differences, that can lead to displacement of centers of axes. How to use UnoJoy software: 1. Upload the "simchair.ino" sketch to your Arduino with an Arduino IDE. 2. Install...

When printing this jig, the only supports needed are below the two alignment fingers. 1/2" PVC - Metric Drill Bit [1/2" PVC Drill Jig - 12mm Bit - 1" Spacing](https://www.thingiverse.com/thing:5137859) [1/2" PVC Drill Jig - 12mm Bit - 1.5"...

This uses the same roller/spacers as the lower guide, so just print two sets of those. ...There are four machine screw holes (use them with 4mm screws and T-nuts), you only really need two of them, the extras are in case you want to move it further out...

For the same price of one tent pole could buy 2 x 6.5m lengths of Al tube, and a roll of filament. Took a few attempts but the twist lock cams were very easy to design and print and worked far better than expected.  The larger version...

Post-Printing Caravan Loft Bed DIY Instructions This model shows how to inexpensively retrofit a loft bed into a caravan. A field bed and some wood from the hardware store serve as the base. The loft bed is intended for children as a sleeping place....

I liked the idea, but I wanted to change some things: - plastic rolls instead of metal bearings pushing on the glass - position closer to driven rear gears where the force is needed to keep the gears in contact - easy to replace one drum with another...

This star ornament was printed in white PLA at 200C and the printbed heated to 65C. You might also be interested in my <a href="https://www.thingiverse.com/thing:3247849">Star 1, </a><a href="https://www.thingiverse.com/thing:3247833">Star 3</a>...

*** Do not print this in PLA as it will melt or sag inside the car *** *** You must provide a charger *** This design is tailored for a 2019 Highlander, but it should also fit 2017-2019 models; I am uncertain about compatibility with other years. I...

The difference is only in the visible layers, for ease of use. Update 20190819: Added a german version for 3.5mm plywood. Update 20191015: Placed the small parts in containers Post-Printing Assemble instructions The photos after the SVG file show...

El Firmware esta compilado para el chip F103 y F303, si tu kingroon es el último modelo necesitas compilarlo para la versión SMT32F4 (mks_robin_nano_v1_3_f4) Link of marlin firmware 2.1.1 (vertical screen)...

This set includes all the printed parts which go along the metal plate (source form e.g. <a...

The system interacts with an on-device embedded webserver, and I've used the same prints for multiple brands of blinds.\r\n\r\nCheck out the pictures and animations showing how it all fits together.\r\n\r\nI previously had two code bases for MQTT and...

When printing this jig, the only supports needed are below the two alignment fingers. When you import this part into your slicer software, it will likely need to be rotated to lay flay on your build surface. 1/2" PVC - Metric Drill Bit [1/2"...

Build: Print the button and plate. Remove the support material. Fit the button into the plate to make sure they move freely. Trimming might be needed. Place the pen spring in the button and insert the button into the plate. Make sure the button...

After numerous requests, I also included the Z-probe for the Bl-touch in the gallery photos.Below is a guide with very simplified photos in Italian and English versions, and at the end of the article the settings used in print (at least for me.) Good...

There is also an experimental EDF holder, not even printed it yet, that would attach to the Body Lid or anything else. The base can be fitted and the two parts glued together. Just an idea but worth putting here. Again saw a Flite test plane with...

How to make You can print all parts without support. Place on the build table as supplied. Circuitry is exactly as same as former thing named "Minimal Mechanical Digital Clock with Network Time Acquisition", https://www.thingiverse.com/thing:4931539...

Printed with CR PLA at 60mm / second 0.2 layer height with 0.4 nozzle 205 ° C hotend 60 ° C bed temperature 100% infill with tree support 45 ° --------------------------------------------- Deutsch: Dies ist ein Remix des Pi Drawers. Leider hat das...

Strengthened the nose of the vehicle by printing it in Ninjaflex 70% infill or ABS. 6. Created a new FrontWheelHub that allows motor wiring to enter at the correct spot. 7. Added hooks for motor wiring in the front part. 8. Stiffened the pushpin and...

Print top.stl, middle.stl, bottom.stl, and 4 pin.stl. Refer to the exploded view and attach pins through precise holes in these parts for robust construction. There are some special steps you need to follow here: 1) You may find it useful to...

With the exception of part "Rear V3 P2.stl" all parts can be printed without support. Layer height 0.2mm, infill 35%. The holes for the LED may have to be redrilled to match the diameter of the used LEDs (indicator LEDs 3mm, all other 5mm). The...

... If you want to create a stand for your transmitter, print two "X10S_stand.STL" parts and attach them with a standoff. I've also included a JR module bay cover, remixed from https://www.thingiverse.com/thing:513861, which has space for angled pins.

Details and links in the description below. Print instructionsI  used Fusion 360 for this project. Thank you Autodesk for letting me  play with your amazing tool! </p> <p><strong>NOTE</strong> The Fusion 360 file attached as a ".f3d" file but the...

... or peat swell pots stand is rather warm than cold compared to glass or metal. Print parameters for me: Infill 10% Layer height 0,18mm Speed 60mm/s Speed 1st layer 20mm/s Outer contours 3 Translated with www.DeepL.com/Translator (free version)

The lamp used in this setup is an Aglaia 4W LED touch-control lamp featuring a clamp base that was removed to accommodate a longer M6 x 20mm screw for mounting on the printed bracket. The non-conductive material of the bracket prevents electrical...

I also made the spacer shaft shape wider so it is not as hard to print, nor as fragile to handle. I also eliminated a few of the sizes that I felt were not necessary. --- This is a PPC (Pixel Pipe Clip) spacer tool that will help you accurately...

I Haven't printed it but I'm confident that it'll fit fine. Update 28/07/17: A gallery with larger photos: https://imgur.com/gallery/p00SB Original text: Whilst I don't have any personal interest in altering the grip for other versions of the...