3d printed centrifugal compressor

The box back design for each car is similar in design since I want it to be seen as a set.Print SettingsNozzle size = 0.4 mm (minimum, smaller better)Layer height = 0.2 mmFilament change layer for colours on "300ZXBoxBack":1) Start (Colour of the...

Print at 0.4mm nozzle, 0.2mm layers, otherwise all design tolerances will be wrong. It is a good idea (maybe essential) to specify 0.4mm wide outer perimeters in your slicer. PLA works fine. Supports are required, but only because of one very...

Various layouts to organize components and tools to keep everything close by so you can make repairs without leaving the table Print instructionsUn pequeño taller para poder trabajar en el salón de tu casa sin quemar nada y teniendo todas las...

Here is an example of how you could extract and print these lists in a Python script: ```python import json # Assuming that the provided JSON string is in a variable called 'json_str' json_str =...

I printed the part using supports which are only necessary for the corners to the upright face. -- x -- I've also included a camera housing for the rear camera (plus fittings). It is intended that this will be attached to the upper plastic trim...

English : Soon version 2 compatible linear rails (as well as wheel), and easier to print. Do not hesitate to like it encourages! After some research on different sites, apart from paid designs, printable cable management kits are rare. I...

[7] Thing Title : Tweezers (single print) Type 1 Simonwlchan created a set of precision tweezers, made available under Creative Commons - Attribution on thingiverse.com. [7] Thing URL : http://www.thingiverse.com/thing:1081911 Find the detailed...

This is a thing I call the Sand Raker, it is a very peaceful print when finished and put together. https://www.youtube.com/shorts/fRqaw5RR5FI A kinetic sand piece that rotates via an electric motor with a pinion gear of 11mm, and rakes the...

The major innovation in coins the Byzantine’s made was to have the emperor face the front rather than print a profile. Most US coins would then adapt the side profile and bank notes adapt a front facing image, if not cocked to the side just slightly....

If you want to use Anet's original M5 screws/t-nuts, just print the parts with 100% infill and drill out the mounting holes with 5.0 or better yet, 5.5mm (to give you some alignment room) drill. Edit: Full screw list, as requested: * 10pcs of 412...

:) My fav PLA on Amazon Italy: Tianse PLA Sunlu PLA+ JAYO PLA+ My fav Resin on Amazon Italy: Elegoo ABS Anycubic NOVA3D Rapid Resin Print Settings Printer: Alfawise U30 Rafts: No Supports: No Resolution: 0.2 Infill: 20% Filament: Tianse PLA White...

It is very important that there are no gaps between the screw and the walls of the tube, so if the screw is rubbed it should be so, it will quickly get used to the walls for this if the printer prints in plus, there are screws in minus. The back...

It was not intended for printing purposes. I wanted to design some custom cases for CHIP and I always start by modeling the subject before moving on to designing accessories. However, until I had the actual CHIP board in my hands, I couldn't even...

I had just finished printing and attaching the V7 fan duct when I took that pic, so I know the whole thing works. However, the picture shows an earlier rendition of the carriage. I moved the inductive sensor mount to the right a couple millimeters,...

It only added a couple of minutes and grams to just go with a solid print. I renamed the other files for clarity. I'll add more info as things are tested and refined.</p><p>The parts list is as follows:</p><ul><li>1.5mm (1/16") silicone rubber in a...

Mount the printed heatblock with the front and back parts of the mold, fix the whole with 2 screws. Make sure it's tight enough. (pictures 7 and 8) 2. Put the freshly assembled block over the bottom part of the mold (picture 9). Make sure the holes...

This is better than putting an oscilloscope probe in your helping hands. Print instructionsRoadrunner Probe Revision A Released 2020-10-04 Copyright (c) 2020 Josh Myer josh@joshisanerd.com Released under a Creative Commons CC-BY-SA license What is...

Please reorient the STL when slicing and printing such that these features face up. ** Note: 2022-02-04 -** the original has been revised to remove any isolated (single square) "towers", called the rev. 2 version. These were found to be weak and...

___________ The whole Space Pirates collection comes pre-supported and has been thoroughly print tested. It was first available on our Patreon channel in April 2021. ...Our Patreon creates different collections of sci-fi miniatures each month -...

Make sure to print the models with minimal infill, - they do need to float after all. There are two main pieces in the kit which we add magnets to: the IgG (antibody) and the Ag (antigen) models and it is*really* important that we insert the magnets...

* The final touch was designing and printing a small adapter for a power socket (similar to this one) I happened to have. * I drilled 5 small holes in the back of my tablet, fixed the power socket there using my adapter, and soldered the wires...

I use resin to print it myself due to the higher precision. If you own a soldering iron you can also solder one of the poles of the motor to the case itself and straight connect it to the rca-connector like I did in the photos attached. (photos to...

Best printed with PETG at 100% infill. The larger version (stl and 3mf included) are specifically sized for the newer style pumps that use the clip on nylon base. They will work with the screw on style metal base. Usage of the mold/die remains...

It doesn't cost you anything extra, but helps me out a lot :) Both links in this post are affiliate links. Print instructionsCategory: Hobby Summary Update: I added a second version of the top part of this case, which has a cut-out for those who...

I added the printed parts to it. The latches are removable and allow the cover to be released with the beetles. For that I use an M6 rod which crosses all the pieces of the slice. BE CAREFUL to only glue the end caps to the rod once the other parts...

These are an assortment of Dust Collection Accessories that I've printed. I may be adding more as I need them or possibly upon request for something. I've also added the actual dimensions to all the parts to make it easier for you to make sure these...

Erdhummelkasten&nbsp;DetailsOb Marienkäfer, Schmetterling, Hummel oder Florfliege. All diese Nützlinge finden in diesem Insektenhaus einen willkommenen Brutplatz und Unterschlupf. Diese Werkpackung ist konzipiert, dass für EINE! der oben angeführten...

I first encountered the idea for this type of robot in a biomedical article, presented as a potential new candidate for exploring the human colon due to its simplicity and ability to navigate confined areas....

Then generate and print one using this bearing generator. I've use it to generate slide and ball bearings for EMT electrical pipe and 8mm rod. There are lots of parameters with defaults for most settings. This design requires omdl.The ball bearing...

I have no idea if it will work with the wired version.\r\n\r\nParts needed aside from printed objects:\r\n\r\n- 4mm diameter chrome steel ball bearings (available in a package of 100 from VXB.com; you'll need no more than half that)\r\n- 623ZZ...