3d printed clockwork

All parts are printed with PLA plastic, everything fits on a standard 200x200 mm table, but it is advisable to use 220x220 - you need literally for a couple of parts to minimize support. Assembly video: 1)...

The box back design for each car is similar in design since I want it to be seen as a set.Print SettingsNozzle size = 0.4 mm (minimum, smaller better)Layer height = 0.2 mmFilament change layer for colours on "300ZXBoxBack":1) Start (Colour of the...

[7] Thing Title : Tweezers (single print) Type 1 Simonwlchan created a set of precision tweezers, made available under Creative Commons - Attribution on thingiverse.com. [7] Thing URL : http://www.thingiverse.com/thing:1081911 Find the detailed...

with a smaller diameter printer nozzle, it might be possible to print that wall thinner. Additionally, the FC file is really only recommended for worn out darts, or for a shellshock with an upgraded spring. ... Marked as WIP ~~for the FC files, but...

This is to allow for easy switching of 6V battery to USB power and vice versa, without any alteration on the wiring side.Caution: Make sure your LEDs polarity is correct before you solder them in place (refer to the manufacturer design drawing for...

There is a version (1c_p1.stl and 1c_p2.stl) that is cut for easyier printing on FDM Printers and a Version (1c.stl) that isnt cut. 2: Its Basically a hinge in Sector mechanicus Style that allows you to make ramps or drawbridges. It comes in 3...

I printed and tested it with four 10 W blue LEDs (450 nm wavelength), but other types and wavelengths can also be used. Using the 10 W LEDs shown here, an 80 mm fan must be mounted to avoid heating the reaction vials above 30 degrees C. If lower...

This model was almost perfect, but when I printed one out, it turned out to be a bit chunkier than I really wanted. So, I figured I'd take my own shot at it and came up with this. My requirements were: * It had to match an authentic full-size...

Assume structure can move only rightwards from starting points at given array perimeter += (future_value - current_value) + (shape[1+i] == '1') print(perimeter) ``` Note: `0`s or non-matching nodes could be part of structure, though no code will...

for those who download an try it, all i did was use m4 bolts stuck inside the ends of the tubes after going through the arms then zip tie around the threaded section of the bolt to keep it from slipping out, but do whatever works best for you, i...

... an STL file. The included STL was created while experimenting with TinkerCAD. It's still very much a work in progress, so suggestions and tips are welcome! Print Settings Printer Brand: RepRap Printer: Prusa i3 Rafts: Doesn't Matter Supports: No

If your looking for the original look the v1.0 release at my Github repository: https://github.com/kellyegan/Arduino-Mounting-OpenSCAD-Library The library uses tbuser's pin library for the pin mounts: http://www.thingiverse.com/thing:10541 There are...

- car fuse holder with adequate fuse - actualy not necessary as Dig-Uno can handle up to 10 Amps of current and is already fused, but I just never push the main power through the controler, can be skipped to simplify things Parts of this are...

Mount the printed heatblock with the front and back parts of the mold, fix the whole with 2 screws. Make sure it's tight enough. (pictures 7 and 8) 2. Put the freshly assembled block over the bottom part of the mold (picture 9). Make sure the holes...

blue lines or infill) should be ignored. Post-Printing Assembly Guide Tools needed:* ca 10 wooden toothpicks, 2mm diameter white glue. The one that dries in 5 minutes works best for me.</li> <li>adhesive tape to keep pieces in place, while the...

The built-in socket has the advantage that no cables can be seen. Tools you will need: (see the pictures) Hot glue, super glue, soldering iron, screwdriver, ... Print instructionsCOMPONENTS: Attiny85...

This miniature comes with optional presupported files for resin printing. These files come as ready to go STL files or Lychee files if you wish to edit the supports for your custom needs. You can find my latest releases over on my Patreon!   The...

... Uno. You may also write your own software. I'll also consider requests for a free copy. Send me your request. Print Settings Printer: HyperCube Rafts: No Supports: No Resolution: 0.1mm Infill: 80 Filament: HatchBox PLA Grey Category: Puzzles

Plus more being added please see table belowSorry Painted in lettering and not double colour printing, Found a very light soft grit sanding made using the fibre tipped acrylic paint pens easier to use.&nbsp;Taken from...

----------------------------------- What you will need: * Four of the Corner Posts printed in your choice of plastic. * Two strips of polycarbonate strip 1/8" thick, 4" wide, 2 feet long. (Available from McMaster Carr in the USA part number...

... professionally done and designed to remove beautifully (provided you have dialled in your printer settings). They are guaranteed to give you one of the best printing experiences you've ever had! Are we allowed to use the term "printgasm"?! ...:-)

You can automate it by printing this gearbox that will snap into the mechnisim.I have been successful at driving it with plastic 9g servos after modifying it to be 360. I highly recommand using metal gears which I plan on doing as I already had lost...

There is a new version of this carriage at https://www.thingiverse.com/thing:3615464 AND an even newer one at https://www.thingiverse.com/thing:3688067 ** ** I'd recommend that newest version instead for better rigidity and simpler printing and...

By any means you are now scared to do this operation, I highly suggest you ask someone with expertise to help you on your endeavors.You have been warned.Step 1: partsFirst you need Noctua nf-f12 for the psu and Noctua NF-A4x10 FLX 12v Version.you...

This is my over complicated / over engineered solution to prevent humidity from ruining my filament while it prints in my garage. The spool sits on the rollers inside the container and feeds out a tube on the bottom. The roller assembly has an...

Also, the "spikes" on the gripper didn't print well and had layer separation. The gripper is the part that connects onto the end core which pulls out. It uses a screw to tighten it. There are 2 gripper versions based on if you have the normal...

electrical conduit pole. Print instructionsWhy I Built It I have an outdoor weather station that has batteries inside the instrument array. Changing the two lithium AA batteries once per year involves getting on the roof which is a PIA, so the idea...

This is a ventilation system for an IKEA Lack enclosure.The top and bottom flanges have a “key” that will align the two halves so that the screw holes line up as well as the notch that can be used for servo and/or fan cable management if you wish to...

Buck Converter (to power my 12v cooling fans) Order of Operations !!!CAREFUL When you are done printing and are removing supports, make sure to be very careful on the Mainboard side. There is a 5th screw that is buried in the support material so...

NOTE3: If you decided to print all of these parts with some others you made yourself, don't come crying to me if nothing fits. This design is not complete and not tested at all. NOTE4: (This is for the future) This design is designed to work with...