3d printed game console

Key features: - low profile with 22mm (depending on T2 extender used) - integrated stray light guard - camera rotation possible - thermal isolation from camera to filter (especially handy with heated Etalon filters) - tested with a 500g camera...

If a defined limit is exceeded, a signal is transmitted to OctoPi and the print is paused.Zusammenbau/AssemblyElektrische Bauteile/Electrical components:Die benötigten elektrischen Bauteile können dem Schaltplan entnommen werden./The required...

And I'm happy to report that with these boards, I've had zero read failures from the SDCard on any of my three printers, and they've logged many hundreds of hours of printing.\nI believe I can safely claim they have completely resolved my SDCard...

Blocks with other angles can easily be modeled and printed if needed. It should be noted that the complementary angle to the one shown on the gauge can be mitered by placing the material against the other face of the miter gauge. The shooting...

I removed the water cooling system and installed 40mm fans instead, which work well and provide better quality prints than the original Anet A8 printer. Therefore, I highly recommend upgrading to this system. Update on October 26, 2019: The frames...

Can be printed with a moving head. Arkham Horror investigator - the professor by Craigen https://www.thingiverse.com/thing:4649571 Longboi Trophy by HiyuMarten https://www.thingiverse.com/thing:4706958 Stoat by Davision3d ...

I have started replacing all of my RPi 4B cases with these while I wait for my RPi 5s.Have also included a number of optional attachment brackets and feet that can be screwed onto the case for specific needs.Print recommendations: - Slice cover...

You’ll need to print the following and its best to fit in this order: If running the V6/Dragon carriage mod then fit the cable retainer and cable into it first, skip this step if you’re not. I’ve included a few options you could use: Cable retainer...

Bollards (cross)- print several pieces and glue in vicinity of chocks. Ballast tanks can be filled through ballast vent pipes and emptied by syringe with flexible pipe connected to sounding pipes. Pay attention during ballast operations- excessive...

Refer to the link below for more information and print file(STL). https://surplusperson.tistory.com/800 If you found my designs useful, please donate what you think it is worth to my paypal.me. Your donation will be useful for a new housing...

It is slightly overwheeled, the S-class has smaller wheels than the Jinty, but it is close enough for a reasonable approximation, and if anybody fancies making a specific printed or brass chassis, or just rewheeling the Hornby donor, then please let...

(At least in my setup, if the original z-axis endstop was used, you could wire this in parallel as a backup, possibly.) The part is best printed in ABS, PLA will warp over time. Instructions Use...

I increased the tolerances a bit in the last version 1.1 but I didn't printed it because the version 1.0 is already working good for me (after sanding). So I hope it will be ok for you. Anyway, you will still have to remove the supports and sand...

... Some part coolers like the "Petsfang" & "Bullseye" seem to crash into the camera housing during autobed leveling. Many thanks to "acwest" for pointing out that problem and his solution! ===================================== Have fun printing!

Make sure to set the ON and OFF milliseconds to the recorded time from step 1.Solder the led ring:GND > GND5V > 5VData In > digital pin 6Solder the buzzer:GND > GNDPLUS > digital pin 10Solder the relay (Make sure to make the relay detachable using...

Needs plenty of support when printing it. Please use the shortest machine screws you can for each of the fittings. You need to heat press the nuts all the way into the recesses. Use countersunk head machine screws for the hotend clamp as the top...

Parts: * 2 - 5015 Radial Fans*: link to a 24V version; you might need a 12V version depending on your power supply * 4 - 5x5mm magnets*: for mounting the cooling duct * 2 - 2W 12V LED modules*: wired in series or parallel, depending on your power...

This print took me about 17hrs on my Creality CR6-SE as I wanted it to be super solid and smooth. This palette is made to fit a 3-layer storage container from walmart...

If you want to support my work, you can contribute with me by donating to this PayPal account. Print SettingsRafts:NoSupports:YesResolution:0.3Notes:If you set the wall width to one filament line (0.4~0.6mm) and the infill overlap to higher...

... is how we made it, it's a personal project, so it's ugly in places. I'm just putting this up here in case anyone wants to do this, or do this differently, or use it for something else. Or just print an overcomplicated Bender head, idk. ... Peace.

This kit is presupported, but also includes unsupported STLs for those who want to print in FDM or would prefer tohandle their own supports. ...If you feel inclined to support my work (and get access to previews of upcoming work and voting rights to...

Motoren: https://www.amazon.de/gp/product/B00LCV4XUO/ref=oh\_aui\_detailpage\_o06\_s00?ie=UTF8&psc=1 Kamera: https://www.amazon.de/gp/product/B00VSLHQZM/ref=oh\_aui\_detailpage\_o07\_s00?ie=UTF8&psc=1 Empfänger 2,4GHz Hott:...

(quick post to share files, more info and tutorial coming soon!) https://youtu.be/96DQsjyok3U - print parts on the side (rotate 90°) for best durability and performance...TPU is perfect but I tried PETG and it works fine until you destroy something...

This saves on PLA usage, drops print time from 10.5 hours to 7.5 hours according to CURA, and makes it more universal for phones with cameras in slightly different locations. The fingerprint sensor in the back is now accessible, and it's lower...

My first prints with this thing showed an improvement, but only time will tell whether I was right. ;-) See the file Details.pdf for details and mounting sequence. Again, the Y-Carriage_for_20x20_V-Slot_Rail_Right and...

... to control the servo yourself, so don't ask. Added servo_holder_only.stl on request. This is the servo holder without the space for the electronic components to control the servo. I did not print this servo only variant as I don't need it.

Printer Settings Printer: Migbot i3 Resolution: .2 Infill: 30% Post-Printing Assembly The Z-Axis adjustment block rides up/down on the outside of the front left leg (near the top). Inside the sliding adjustment block, two 8-32 nuts with a small...

http://www.thingiverse.com/apps/customizer/run?thing_id=58001 Instructions Using the following options: image_rotation = 30 degrees to enhance viewing pleasure pattern_shape = a geometric design choice with six sides to create complexity 5cornerR = 8...

However if your task has the property such as finding out paths between the various unvisited nodes where some paths can have multiple lengths because it was given in both weights so then this needs another method of sorting by distance to reach...

Now have fun printing and installing the brackets. A little tip: Use heatsinks with thermally conductive adhesive and not with the adhesive pads. These are no good. If you like my design please show it with a like or a make here on Thingiverse. ...