3d printed name tag

This transformation enables my DaVinci to print PLA at 80mm/s with impressive accuracy and minimal noise, eliminating the screeching sounds associated with fast movements. Travel speed has increased to 200mm/s. This mod necessitates that Repetier...

If you use Marlin, you could set in Configuration.h: ``` #define X_MIN_POS -15 #define Y_MIN_POS -15 ``` Print with ABS or with any rigid plastic which works in your temperature range. Take into account that the mount contacts the stepper motor which...

To make one, follow these steps: Select from the available options: * The back angle of your phone: 10 degrees * Whether to counter-sink screw holes in the center plate (screw count, depth and diameter are irrelevant): no * Wall thickness of your...

Most models have built-in fan speed controllers which switch off the fan at idle and vary the fan speed according to the PSU load. Compared to the original cover design by sneaks, I've changed the following:thickened upper PSU mounting area to...

I removed the water cooling system and installed 40mm fans instead, which work well and provide better quality prints than the original Anet A8 printer. Therefore, I highly recommend upgrading to this system. Update on October 26, 2019: The frames...

If you still think you want to do it, I'd recommend my slot-lock attachment system as seen in TauZ and Tau brace.\r\n\r\n**Update** I redid the foot so it screws directly into motor frame which is far better and simpler to print\r\n\r\n**Update** I...

... my workflow and as long as nobody complains you are forced to do so too :P. But don't be afraid my friend 3mf is as simple to use as STL. PS: If you only need some protection for the camera u can just print one bumper and cap and you are set. ...

This is basically the **Customizable Better Temperature Tower** by *kmsd3d* including: - several pre-rendered stl files for various filament types - a list of layer change settings - the original customizable OpenSCAD file - an Python3-tool to create...

print a large end and glue it to the screw head. I'm attaching this as a .STEP file... I'd rather you take a look at this F360, Freecad, etc... it works great as is, but I'd love to get some feedback. I'm open for any suggestions on...

It's essential to print this component in HIPS or a similar material that's more heat-resistant than PLA. I've tested it with PLA, and while it works initially, it deforms and becomes brittle over time. Additionally, the cooling duct was designed for...

Hobby Tool Holders This is an initial set of compact hobby tool holders the purpose of which are: - Short term tool storage for tools being used on an active project - Organization to help keep the bench cleaner - To help facilitate rapid tool...

You only need to print two sets of screws. One for the north celestial leg and one for another leg. The screws have 80mm length and can level at ~50° incline, so a distance of ~40mm. In the middle of the inner screw is a marker that shows the...

(3 Male, 1 Female).1 x Thompson SMG as a stand alone weapon.1 x Pair of Female arms wielding a 1912 Winchester shotgun.1 x 1912 as a Rifle-Stock joint compatable front end.1 x Pair of Male arms wielding a M1919 Browning machine gun modified into a...

Accuracy depends on a multitude of factors, including the print quality, the gauge's accuracy, and the saw itself. I was able to achieve precise cuts within a few thousandths of an inch. Please share how it performs with your tools. Additional...

I used the #19 drill with the depth stop (as described in the Ford Flat Head Assembly Structures for the threaded inserts) to drill holes for the magnets in the block. The Display Base was too big to print as a single part on my printer, so I split...

For this, you will need a few parts: EzStruder direct drive or bowden doesn't matter Low profile motor support printed part (see my thingiverse thing) 30x30mm Fan shroud v3 (or other thingiverse thing version) 3 fans of 30x30mm (or different size,...

To achieve this, you can adjust your printer using the following template: https://www.thingiverse.com/thing:5413456 It allows you to adjust the feed rate specific to your filament to obtain precision of the order of a hundredth of a millimeter,...

Required printed parts: 2 each - Thing1 1 each - Thing2 1 each - Thing3 1 each - Thing4 Required purchased items (blue LED used, white would be better): 1 each - 5mm x 20M Double Side Adhesive Thermal Conductive Tape For Heatsink...

I never printed outside the heat bed (300x300mm) although this printer could do much larger than that. Also, it took a lot of space and it was not portable at all. So a new printer design came into my mind. This printer has everything Big DIY Printer...

... it seems to work better, I will try another size that reaches the top, when I reach the 35cm. Anyway, the improvement is extraordinary, the squares of the photo are printed with 1 single layer of skin and without filling. ... Translated by Google

UPDATE 2019-04-26: added redesigned chain for easier print "Chain Whole V3" and fixed bug, both sides needs equal number of chain parts, old design has one missing chain part. Old design for some people fused too much, couldn't get it separated. New...

This mod requires a new XY end-stop bracket that houses both end stop switches (I suggest printing it in >50% infill TPU so it has a bit more flexibility to insert the switches, but is still rigid enough - not loose, not crazy tight) , and a few...

Print a bunch of cleats and bollards, they are always good. If you do make this, please please post a make. I'm very keen to see other people getting some use out of these files! ... <iframe width="560" height="315"...

The printed part worked first time once supports were removed. However, holding the case together after destroying the flanges and rivet was easy: I drilled and tapped the remains of the rivet to accept a short countersunk bolt found in my computer...

This miniature comes with optional presupported files for resin printing. These files come as ready to go STL files or Lychee files if you wish to edit the supports for your custom needs. You can find my latest releases over on my Patreon!   Judge,...

Bill of materials: Printed: 1 x CASE MAIN 1 x CASE FACE Bought: 5 x Banana sockets of different colors (https://item.taobao.com/item.htm?spm=a1z09.2.0.0.67002e8dUgkbaW&id=561956389062&_u=52q9f1426ddc) 1 x Potentiometer 50k Ohms...

For better print quality all screws holes in the Cover (and also above the nuts holes in the main body) are covered by thin layer (0,24mm). For better understanding please look at Cover in your slicer (level +22 mm). Just use drill or proper screw...

Human: [Update 2019-07-01] #Don't print this as of now, at least with PLA After some days of usage I've noticed the spine parts and/or assembly are not sturdy enough. The combined weight and dissipated heat from the components (around 250 W under...

The switches are activated by two tabs mounted under the bed with M3 screws, nuts and printed M3 T-nut converters (T-Nut-M3.stl). The upper Z-Axis switch is clamped to the Z-Stepper motor RHS mounting posts, while lower mounts simply clip on. Ensure...

This is a remix of the device at the following URL: https://www.thingiverse.com/thing:4341389#Print%20Settings This is significantly different on the outside versus the original model. I needed to change the shape so I could mount this directly on...