3d printer as plotter

I made this desk light as a little weekend project.News:see a second shade here: https://www.printables.com/de/model/177634-spherical-shade-for-my-bright-desk-lightan uplight mount is available here:...

He fled first to Switzerland and then in 1816 to England, where he became popular for a time due to his status as an Italian patriot. Foscolo supported himself through teaching and writing commentaries on Dante, Boccaccio, and Petrarch for The...

As it sits very close to the heated bed, I would recommend using PETG to prevent warping. Bed Clearing Script: M140 S0 ;turn off heated bed G4 S1800 ;wait for 30 mins M17 ;enable steppers G90 ...

More information can be found here.TardisAs base I have used this thing.Print the following parts from there:Base (either ring or solid)Panel with doorPanel (2x)Window (2x)Top ringRoofLamp shadeLamp top From here you need to...

The sizing guide is as follows: 1.) s150/150%: Extremely large, with a flat bottom version reaching 15.25 inches in height and a full version barely printable on a CR10. 2.) Unmarked/100%: Substantial, with a fully printed flat bottom version...

Though the vendor was grateful, those around her saw the witchcraft as unlawful use of magic and called for her to be trialled. With an angry mob yelling voraciously for her to be burned, the very meek Graf of Mitte gave her the choice of being burnt...

This project has been developed as a robot test for young people between the ages of 12 and 15. It consists of a very simple robot programmed with MBLOCKS and controlled from a mobile app. The following files are attached: 1. The assembly folder...

Dimension60 (width) x 40 (height) x 15 (thick) FeaturesElegant-looking retractable drawer pull handle, able to fold flat while not being used, and could be pulled up 45° for easy grip. The folding pin also hides the mounting screws,...

**First-look photo**: The fourteenth reference is from The Hollywood Reporter, where Patrick Shanley shares details about the first look at Joaquin Phoenix as Joker. 15. **Makeup reveal**: The fifteenth reference is from Polygon, where Matt Patches...

Don't use to move the original LCD screen as it will interfere with the bed at its forward limit, unless you displace the screen further left. Finally.... There is a lot of opinion out there about increasing the z-axis rigidity. You read of...

The blocks were designed to fit this specific t-track from Amazon: https://www.amazon.com/gp/product/B07ZV74RR1 The linear rail I used is 330mm in length as well: https://www.amazon.com/dp/B08TQQNLW7 The fan shroud is my other modded design located...

The difference for each name plate are: ###NamePlateAssem: As shown in the picture, it is made for the Advan HKS GR Supra with modelled Advan and Toyota Supra names on it. ###NamePlateHKSOnly.STL: A generic design with just the Advan branding on...

(I also have a Centered shaft transmission, if you need it, reach out on Facebook as I have to update a couple of things before adding here) What you'll need to complete: * Tekno SCT410. You don't need the rear end. You'll have to cut the skid (see...

___ ####Download object holders such as phone clamp, camera plate, tablet holders from [here](https://www.thingiverse.com/thing:4625349) ####Download the vice clamp from [here](https://www.thingiverse.com/thing:4614461) ####Parts for optional metal...

I also added a external axle drive wheel to help with filament feeding if needed and it also allows you to monitor the movement of the drive gear and filament to make sure it is moving as it should. I also removed the Bowden tube connector and...

This allows Vorpal to measure the distance (in cm) to the nearest object in the direction the sensor is pointing.\r\n\r\nFor example, you could implement obstacle avoidance as shown in this video:\r\n\r\n[Ultrasonic Obstacle Avoidance...

**So for a normal USB feed it will be fine**, but as the battery runs down to these levels it isn't. On the specs (just read them after making it): Input voltage: 4-20V Main measurement parameters: run time, temperature, current, voltage,...

I made the chain link first as I wanted it to be able to print without supports and then made it with the smaller bucket but the wife thought it wasn't big enough so I made the bigger bucket. I included a tank tred link for fun so I suppose the...

You can them use as-is or customize them using the 123D design files in the ZIP file.The gripper itself is controlled by an Arduino and the moving slide it's mounted on is run by an Adafruit Motor Shield. The function of the assembly is to sense when...

Scale the height of the "ZNotStop" as required. This component cooler collides with the cable chain, so move the chain outwards and use the longer "BettKetteHalter". Printed all the parts with PCTG. Geänderte und verwendete Dinge aus: Changed...

Secure both ends of this wire as well. With another new piece of wire, connect the NEGATIVE end of the third battery via the holes, run it through the next channel and connect it to the POSITIVE terminal of the fourth and final battery. Secure both...

If you want to print the center triangle in different colors as well, the first filament swap should be made after 4mm height, the others after 5mm each. (PrusaSlicer: 4.20, 9.20, 14.20, 19.20). MMU, Palette or other multi material devices Each...

Alternatively, you can skip parts 4 and 5 and use "z 4and5 alt pistol grip" which has both pieces printed as one. Drop the assembled pistol grip into the white lower, 2, and glue in place.</p><p>TRIGGER &amp; FIRE CONTROL GROUP (FCG):<br>Put the...

###WORK IN PROGRESS### ###What it is### This case is specifically designed to connect directly to a "tape measure yagi" antenna's PVC pipe and serve as an attenuator for foxhunting (radio signal direction finding). It is built around the great design...

... Use this design as you see fit. By the way, Both filament guides and the extruder knob I installed on my machine have conspired to reduce my usable print height by about 20mm! ...The recommended settings include a 1.2 shell and 10% cubic infill.

Not because I think it is final, but because it will serve as an inspiration sitting on my desk.\r\n\r\nPlease feel free to comment positively. Please bear in mind this will not be a scale model, I just look at photos of the Peterbilt 359 and make...

The tubes can connect by glue or an small screw as shown in the detail picture of one brass nut from below. The outer dimensions of the upper bed are 360 by 273mm --> check if this fits your need or the belt will not fit without modifying some...

It is not as wide, so I had to replace the original Ender 5 belt. It does not use a groove mount, instead it uses the 4x threaded mounting holes found on the Phaetus/Triangle Labs Dragon and Dragonfly BMO. With the latter, it will be rotated by...

The PCB Has Space for Additional Inputs and Outputs, Allowing Users to Customize Their Robot Platform as They See Fit. The Design Prints Easily Without Supports. ... Here's an Example Arduino Code: //Nano Full Step Mode //512 Steps Equal 360 Degrees,...

1x token_tray - For rest of the tokens from this expansion ### Mystery Tales 1x mystery_tales_cards - Local Guide & Native cards, Character cards, Insanity cards, Condition cards, Mystery cards, Event cards for scenarios 1-5, Wreckage cards for...