3d printer filament monitor
1946581 3d models found related to 3d printer filament monitor.thingiverse
HICTOP (hic-top / hic top) 3D printer improved filament feeder model 3DP11 the new version (1Q2016) of Hictop printer includes a microswith to monitor filament. the problem is that it make a lot of noise because it don't let the filament freely flow....
thingiverse
This project combines a physical filament monitor, some simple electronics and a Twine to create a monitor that emails you with the printer status; fully operational, filament feed stopped and printer stopped. Instructions The monitor has 3...
thingiverse
This thing works perfectly with my filament spool holder http://www.thingiverse.com/thing:1295883 Print Settings Printer: kossel delta 2020 Rafts: No Supports: No Resolution: .3mm Infill: 30% Post-Printing Assembly attach the monitor to the monitor...
thingiverse
You can purchase the Tunell Filament Monitor at http://www.toybuilderlabs.com/products/tunell-3d-printer-filament-monitor Post-Printing Installation Use M3x8 screws to mount the Tunell monitor to the arm. Snap the arm onto the right-front frame...
thingiverse
A Web Enabled 3D printer Filament Monitor System and spool holder. This setup will monitor and report the following to a custom web view/api: * Weight of filament left (upto 5kg) * Humidity * Temperature * Color of material loaded It also includes a...
thingiverse
... for 1.75mm and 3mm filaments Alarm range 1.65 to 1.85mm and 2.90 to 3.10mm Can be used as out of filament detector ! Available in my Tindie Page Kit : Ready assembled : https://www.tindie.com/products/JasonKits/3d-printer-filament-monitor/
thingiverse
Portable printer monitor for octoprint with ESP8266, 0.96" OLED and lp-e6 battery. At the moment it's really hard to assemble so I recommend to wait for second version. ... Links for hardware: ESP8266 - goo.gl/bEHqeL 0.96 OLED - goo.gl/CjfoVP ...
thingiverse
Mount set for the Tunel Filament monitor found here...http://www.toybuilderlabs.com/collections/best-selling/products/tunell-3d-printer-filament-monitor?variant=963597848 I rounded a few corners on the main brackets and made the back plate thicker...
pinshape
http://www.toybuilderlabs.com/collections/best-selling/products/tunell-3d-printer-filament-monitor?variant=963597848 I rounded a few corners on the main brackets and made the back plate thicker plus added slots for inserting M3 nuts on the rear...
prusaprinters
It will work with any printer that uses filament on spools - though you will need to use a spool holder that uses ball bearings like those referenced in the instructions. In contrast to the minimalist filament monitor I created specifically for the...
thingiverse
A previous simpler tracker design of mine did this at the back of the printer, but there's not much space there (and none at all if you are using a dust filter like the one I linked to above) - and threading / attaching a filament to a monitor would...
prusaprinters
I printed up a case and a simple mount for the Gel packs to mount inside the bucket. I have included a solid lid if you have a different board you might like to use. Here is a list of the parts I used, you probably have most of this stuff so the...
thingiverse
I was working on a remote moisture monitor and just for the fun of it I threw it in one of my buckets to see what the humidity was inside the bucket after it was closed over night. I was shocked to see I was at 45 percent the next morning. So I...
thingiverse
made the printer monitor portable, wanted it to look like something, so found my old gameboy and made a scale model that would fit the electronics. For the Battery i used a 1000 mah lithium battery. for charging the battery and supplying 5v to...
thingiverse
this is a bracket that fits on to your 3D printer that can hold an LCD screen in it. ...The screen just sets into the bracket with no screws or anything needed
pinshape
You can purchase the Tunell Filament Monitor at http://www.toybuilderlabs.com/products/tunell-3d-printer-filament-monitorPost-PrintingInstallationUse M3x8 screws to mount the Tunell monitor to the arm. Snap the arm onto the right-front frame T-slot...
thingiverse
Filament filter for 3D printer. 1.75mm filament. ...You will need to get a sponge for this.
grabcad
3D printer filament extruder complete CAT designs(https://repetierinstallation.blogspot.com/)
cults3d
This is a stand that is used to support your 3d printer filament wheel while printing.
thingiverse
Hubs for 3D printer filament. One hub is 52mm ,the other is 72mm and they both fit a 10mm shaft. This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/lb6kx6xTd4S
grabcad
This little clip can be used to clamp the end of your filament (of a 3D Printer) to the spool. It won't unrole then :)I did both filament sizes: 1.75mm & 2.85mm, but I also added a version with equations, you can then choose between different...
thingiverse
Edit it online https://www.tinkercad.com/things/jpCjXy0Xuf2 Assortment of clips for 3D printer filament spools. If you have ever tried to untangle a roll of filament, then you realize how handy these are. I normally just print a bunch and put extras...
thingiverse
I have done some writeup about the circuitry required: https://www.randseq.org/2020/02/3d-printer-filament-joiner.html And here, adding an OLED display and rotary knob for a totally independent unit that does not need to be tethered to a PC:...
thingiverse
Please watch my Youtube video tutorial on how to build this: https://youtu.be/NhnJ6pyhUBw GRABCAD LINK(for 3D model files in .ipt/.iam/STEP format): https://grabcad.com/library/3d-printer-filament-roller-hex-nut-version-1...
cults3d
With this file you can 3d print a custom filament spool holder. Modeled off of the anycubic basic spool holder that came with the I3 Mega printer. You can print each part whatever color you desire! Completely 3d printed! ... Prints easy with no supports...
pinshape
Summary This is a simple filament guide, designed to bolt to the frame of a 3D printer. I couldn't find a simple guide on the various maker sites, so I quickly put one together in Fusion 360. I'm happy to send you the file, if you wish to modify...
thingiverse
... to those filaments. Just download the .jar file and double click it to run it. Java is required to run the program. https://www.youtube.com/watch?v=3JT2ombsjBg Code is here https://github.com/MrOwnership/3D-Printer-Filament-Tracker Post-Printing